Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Event temperature increased to 25 degrees Celsius. Determine the normal stress on the steel due to the change in temperature. Steel Brass Copper Est = 200 GPa ast = 12(10-)/°C abr Ecu = 120 GPa Epr 21(10-")/°C acu = 17(10-")/°C 100 GPa %3D Acu = 515 mm² |3| 200 mm2 Abr = 450 mm2 Ast -300 mm -200mm 100 mm 20.11MPA, C 0 15.57MPa C

Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Event temperature increased to 25 degrees Celsius. Determine the normal stress on the steel due to the change in temperature. Steel Brass Copper Est = 200 GPa ast = 12(10-)/°C abr Ecu = 120 GPa Epr 21(10-")/°C acu = 17(10-")/°C 100 GPa %3D Acu = 515 mm² |3| 200 mm2 Abr = 450 mm2 Ast -300 mm -200mm 100 mm 20.11MPA, C 0 15.57MPa C

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the total deformation on the steel. Steel Brass Copper Est = 200 GPa Ebr = 100 GPa Ecu = 120 GPa %3D ast = 12(10-6)/°C abr = 21(10¬6)/°C acu = 17(10-)/°C %3D Acu = 515 mm² |Ast = 200 mm? Abr = 450 mm² %3D 300 mm- 200 mm 100 mm O -0.0058mm O 0.0165mm O -0.0165mm O 0.0058mm
NEED IN 1 HOUR PLS, THANK U A copper bar is of uniform cross-section and is rigidly attached to the walls as shown. The rod is 5ft long and has a cross-sectional area of 2.5 in². At a temperature of 20°F the rod is stress-free in the configuration shown. Determine the stress in the rod when the temperature has dropped to 50°F. Assume that the supports do not yield. For copper, E = 16x10⁶ lb/in² and α = 9.3 x 10^-6/°F.
The length of the assembly shown below decreases by 0.5 mm when an axial force is applied by means of rigid end plates. Determine (a) the magnitude of the applied force, (b) the corresponding stress in the brass core.
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in aluminum of 80 MPa, in steel of 150 MPa or bronze of 100 MPa. Steel Aluminum Bronze А P> ЗР - 2P outside = 30 mm d inside = 20 mm d d = 16 mm d = 60 mm -100mm- -150mm- -125mm-
A compound bar is subjected to a compressive force of P=556 kN by means of a rigid endplate at the top. If the length of the bar is 876mm, determine the stress in the alurninum core. Answer in MPa. Round off your final answer to 2 decimal places. 25 mm Brass core E = 105 GPa a = 20.9 x 10-6/°C Aluminum shell E = 70 GPa Q = 23.6 x 10-6/°C 60 mm
At room temperature (10 C)° a 0.25-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 130°C, determine the normal stress in the each rod * 0.25 250 mm 200 mm B Aluminum A 2000 mm² E = 75 GPa a = 23 × 10 6°C Stainless steel A = 800 mm² E = 190 GPa a = 17.3 X 10-6PC
In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is Oal = = -90 MPa and the initial temperature 20°C. 2) The final length of the aluminium member. Aluminum Bronze A=1800mm2 A=1500mm2 E=105GPA E=73GPA a=23.2x10-6/°C a=21.6x10-6/°C Gap=0.5mm 0.35m 0.45m
Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the total deformation on the brass. Steel Brass Copper Est = 200 GPa 12(10-)/°C apr Ebr Ecu 17(10-)/°C 120 GPa 100 GPa %3D ast = 21(10-6)/°C acu Acu = 515 mm? |Ast 200 mm2 Abr = 450 mm2 300 mm -200 mm 100 mm O -0.0109mm O 0.0241mm O -0.0241mm O 0.0109mm oooO
Determine the stress on the Bottom of Copper. (in the Unit of MPa), Determine the stress on the top of Copper.
two rods attached to a rigid bar AB with negligible mass . A 101 kN load was applied at the end of this bar. The computed stresses for steel and bronze are Blank 1 mPa and Blank 2 mPa respectively.