Station Station Distance (m) Observed interior angle Adjusted interior angle 102°57' 103° 9' 30" | -0°19'12"| 102° 50' 18" correction OcC obs Direct Reversed Мean A 11.55 103°22' B 13.20 B A 13.20 88°14' 88°14' 88° 14' -0°19'12" 87° 54' 48" 17.42 113°36' 112°48' 113° 12' -0°19'12" | 112° 52 '48" B 17.42 D 10.00 D 10.00 156°06' 154°31' 155° 18' 30"| -0°19'12" | 154° 59' 18" E 13.90 E D 13.90 81°42' 81°42' 81° 42' -0°19'12" 81° 22' 48" A 11.55 Length, Calculated LATITUDE Bearing DEPARTURE LINE m +N -S +E -W AB BC CD DE EA

Q: Please provide your solutions and corresponding illustrations 1. Determine the angle in between two…

A: Bearing is the angle made by line either from north and south. Azimuth is taken either totally from…

Q: 3) Compute the coordinates of the area centroid with respect to the given axes. a b 3 m 1m d- 6 m…

A: To find out the centroid of the section from X Axis and Y Axis.

Q: Determine the magnitude and direction of the resultant force for the force system shown below. The…

A: Force system in which different forces were acting. We need to calculate resultant force for the…

Q: Determine the coordinate direction angle of FR with y-axis.if FR.=190 N F2 = 110 N FR F = 80 N opo…

A: Given data in question  Resultant force 190 N Angle made with xy plane 45° Angle made by (Fr)xy…

Q: Find the interior angles and corrected angles A, B, C, D Find the total area of the figure

A:

Q: a) top most, lef tmost FIND: 6) botton-most, right-most 3cm S.ם r = 1,25 y 125 } 05 Vb cm 1.5 3 I…

A:

Q: Please draw diagram  Answer fast

A:

Q: • Determine the x. Measure it from the y-axis. 120 mm -70 mm 60 mm 60 mm 40 mm 150 mm O 82.85 O 61.4…

A:

Q: Write the basic principle of the vernier scale.

A: Vernier caliper is an instrument used for measuring lengths. It is more accurate and it can be used…

Q: Basic 1. General Use the POLYGON command to draw the hexagon as shown. Fully constrain the hexagon…

A: Given Sample drawing To draw Drawing similar to given drawing with different dimension and the steps…

Q: Find the centroid along x- axis of the shaded area. x - axis = _mm. y ゥー 335 | 600 mm 345 243 O 249…

A: The centroid of give section is calculated as below

Q: The coefficient of uniformity and coefficient of curvature resepectively are: Given D60 = 0.22 mm,…

A:

Q: b)Calculate horizontal components at point C

A:

Q: H. W: Find the lines that are tangent and normal to the curve y = tan x at the point G.1).

A: Given, x1, y1=π4, 1 It is required to determine the slope. Differentiating the given equation,…

Q: how to solve this? missing resultant and missing angle of one force

A: Given data,  F1 = 205 kN Angle of F1 with Y Southern = θ Resultant angle with x = 30° To find out…

Q: R=0.956 m 6.97 R= =0.956 %3D b+2/2d b=7.29-2.828d

A:

Q: 1. Locate the centroid of line ABC B A 250 mm 40° 75 mm

A:

Q: The declination at a point Q is 3* 15 east. The true bearing of a line QR is S 30* 30' W. The…

A: To find magnetic bearing of line

Q: Locate the centroid y̅ for the cross-sectional area of the angle.

A: For centroid calculation total area divided into two parts A1 , and A2 A1 = t(a-t) A2 = at

Q: Determine the coordinate of the centroid (y) for the following section with respect to the given…

A:

Q: Draw in and label the 150 m contour line. 112 152 108 130 162 122 140 170 132 155 162 140

A: Contour lines are the lines joining the points of equal elevation ..

Q: 5. biven a rectangle ABCD's frontal projection. Complete its horizontal projection. a d 0.

A: The plane onto which the Front View (FV) of a multi-view graphic is projected is known as the…

Q: Required: Draw the front projection, the left side projection, the horizontal projection

A:

Q: 5/22 Determine the x- and y-coordinates of the centroid of the shaded area. a 1 | y=k₂√x y=k₁x³…

A:

Q: Which is the radius of curvature of the function y3Dvx at x=2? *

A: Using formula

Q: Problem 3 A field is in the form of a regular pentagon. It is required to determine the directions…

A:

Q: A rectangular section with b = 250 mm and d = 350 mm, if f = 25 MPa and fy = 420 MPa, the depth of…

A: Given data Width of the beam, b= 250 mm  Depth of beam, d =350 mm Tensile strain = 0.006 fy = 420…

Q: Draw the plan and elevation of rectangular plate PQRS(PQ=30mm , QR= 35mm) when it's corner Q is 2cm…

A: - The representation of rectangular plate is shown in figure below.

Q: dy Find if y = 20xeV dx

A:

Q: 33.33 is wrong

A: The rigidities of walls A, B, and C  = 1.0 The rigidity of wall D = 1.5. Force acting in horizontal…

Q: PROBLEM 2: Determine the coordinates of the centroid of the area shown, with respect to the given…

A: Determine coordinate of centroid

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.