Find the interior angles and corrected angles A, B, C, D Find the total area of the figure

Q: a. Determine the force in each member uf the real and the virtual truss shown above. b. What is the…

A: Find reactions:Take moment about Right support:∑ MA=0Cy(3)-100(4)=0Cy=133.33kNTake moment about…

Q: Determine the angle between that the 5 kN force F and the positive sense of the Z axis. F = 5 kN 35°…

A:

Q: Determine the smallest cross-sectional area A required for the members of

A:

Q: a) top most, lef tmost FIND: 6) botton-most, right-most 3cm S.ם r = 1,25 y 125 } 05 Vb cm 1.5 3 I…

A:

Q: Using the double

A:

Q: 12KN IM Am Am

A:

Q: Using Double Integration Method analyze the beam below 25KN 10KN/m A El-120000KNM^2 El-200000KNM^2 C…

A:

Q: For the beam shown, EI = 24 x 106 kip-in² over the length of the beam. The slope (rad) of the beam…

A: Given : EI = 24  X 106 kip-in2 The slope of beam at location B is ?

Q: Use the virtual work method to determine the slope and deflection at point B of the beam shown

A: In the virtual work method to determine the slope and deflection at a point, we have to introduce…

Q: Using the method of virtual work, find the vertical displacment of Point D. E = Ksi 1 inz 29,000…

A: To find the vertical displacement at the point D in the given truss using the method of Virtual…

Q: Explain parallel axis theorem. Determine moment of inertia about both the axis for the profile shown…

A:

Q: Determine the slope and deflection of point B of the beam shown by the direct integration method. 6…

A:

Q: Use the virtual work method to determine the horizontal and vertical components of the deflection at…

A:

Q: 2. How far is the centroid of the cross section above its bottom edge? What is the area moment of…

A: The centroid is the center point of the built up cross section when all the axis in the object pass…

Q: 50 N 25°

A:

Q: For the beam shown in Fig.Q4, use the principle of virtual work to determine (1) the vertical…

A: Given Point force(P)=35KN Uniformly distributed load(q)=14 kN/m Length of AB span (L)=4 m Length of…

Q: AK N zm zm

A:

Q: Using the theorem castilgliano, calculate the horizontal displacement of point D with Castigliano's…

A: Assigning Pseudo load 'P' at D as shown in diagram, P=0

Q: Determine the centroid (x, y) of the parabolic area.

A:

Q: Find the largest and smallest angle changes with their directions at point A, as the unit…

A: total X direction displacement of linesfor aa=+430×10-6 for BB=-260×10-6×cos60=-130×10-6for…

Q: Apply the virtual work method to determine the slope and deflection at the midspan. El is constant.…

A: A simply supported beam AB is loaded as shown in given fig. P = 30 kN w = 5 kNm E = 200 GPa I = 3500…

Q: 4) Solve the following armature using the virtual work method, taking into account A = 3.2 in2, E =…

A:

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A: From the given figure it is required to determine the angle α between AC and AB. And also to find…

Q: y Problem 3 10mm Determine: a. Determine the location of the centroid of the figure, x and y.…

A: Let the given figure is divided into two sections i.e Section 1 and Section 2. Let (x1,y1) and (x2,…

Q: Find the deflection at point D using a virtual method. Show complete solution and dimensional…

A:

Q: 32 kps 05 For the beam shown, estimate the displacement at point B in terms of El.

A: Given: Force = p= 32 kips  To find: Displacement Note: Displacement = Slope and deflection.

Q: Determine the sum of the moments created by the forces shown in the accompanying figure about points…

A:

Q: Determine the slope at point D of the beam shown using the Virtual Work Method. (You can verify…

A: Find the reactions of the orginal beam:∑ MA=0RB10-1505=0RB=75KN∑ Fy=0RA+RB-150=0RA=75KNMoment…

Q: Use the moment-area method to determine the slopes and deflections at points B and C of the beam…

A: Solution;

Q: Find the minimum required value of I for the given beam if point C is noT to deflect more than 1.0…

A: Maximum deflection at C=1 cm =0.01 m E=200000 MPa=200000 ×106 N/m2=200000×103 kN/m2 Consider the…

Q: Use the method of virtual work to find the vertical deflection of the steel truss at joint A (in…

A: E = 10,000 ksi = 10,000 × 103 lb/in2  A = 4 in.2  Determine the vertical deflection at joint-A using…

Q: Use the virtual work method to determine the horizontal and vertical components of the deflection at…

A:

Q: Determine the horizontal displacement at A. Take E =199947.9615 MPa The moment of inertia of each…

A: Horizontal displacement at A

Q: 4- Determine the vertical and horizontal deflections at joint B of the truss shown using the virtual…

A: Given data in question Load 100 and 50 kNArea 1000 mm2E = 70 GPaTo find out Vertical and horizontal…

Q: Determine the magnitude of the resultant force acting on the plate and its direction, measured…

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.