A steel beam, of lengths a = 4 m and b=4 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q = 0 kN/m to q = 4.2 kN/m for AB span; and is constant with q = 4.2 kN/m for BC span. The Young's modulus of steel is 200 GPa. ▲y, v a 5 mm 200 mm I Figure Q.1 9 S B 300 mm b с X

A steel beam, of lengths a = 4 m and b=4 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q = 0 kN/m to q = 4.2 kN/m for AB span; and is constant with q = 4.2 kN/m for BC span. The Young's modulus of steel is 200 GPa. ▲y, v a 5 mm 200 mm I Figure Q.1 9 S B 300 mm b с X

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need answers for problems 13, 14, and 15 pertaining to the print provided. NOTE: If you refuse to answers all 3 parts and insist on wasting my question by breaking down 1 simple question into 3 parts, then just leave it for someone else to answer. Thank you.
Question 1 An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is 3 mm thick in SOLIDWORKS. The engineer most likely used the feature. Chamfer Fillet Hole Extrude
I need help solving problems 13, 14, and 15 pertaining to the print provided below.
Handwriting not allow please And give me complete answer
I need help with this question :)
If the cooling system operates above 100 degrees Celsius how should the cooling system, cooling fans, and thermostat be tested? (80 - 100 Words)
how do i draw sectional view of this object.
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
I need answer within 5 minutes please please with my best wishes
follow up question - for the past two question. (subquestions)
Partial Question 9 Which choices are correct explanations about the scanning electron microscope (SEM)? (Select all that apply.) Visible light is the main light source. The microscope can investigate non conductive samples as good as the conductive ones. Samples need to be polished. The condensed beam does not pass through the specimen, but is reflected from a surface of the specimen and was collected to obtain the picture. Useful resolution range is much wider than the optical microscopes.