Sketch the Colpitts oscillator (using a BJT), clearly showing the modifications from a voltage-divider bias circuit above. (i) Explain the working principle of Colpitts oscillator. In your explanation, include the function of each component and the function of the tank circuit, together with the energy conversions taking place in the tank circuit. (ii) What is the phase relationship of the output signal with respect to the input? (iii) Write an expression for the frequency of oscillation and explain all the terms of the equation. (iv) Calculate the frequency of oscillation given that C₁=C₂=7μF and L=2 H Activate Wi

Sketch the Colpitts oscillator (using a BJT), clearly showing the modifications from a voltage-divider bias circuit above. (i) Explain the working principle of Colpitts oscillator. In your explanation, include the function of each component and the function of the tank circuit, together with the energy conversions taking place in the tank circuit. (ii) What is the phase relationship of the output signal with respect to the input? (iii) Write an expression for the frequency of oscillation and explain all the terms of the equation. (iv) Calculate the frequency of oscillation given that C₁=C₂=7μF and L=2 H Activate Wi

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Write the expression for the output voltage of a balanced modulator
A signal generator having a source resistance of 50 2 is set to generate a 1 kHz sinewave. Open circuit terminal voltage is 10 V peak-to-peak. Connecting a capacitor. across the terminals reduces the voltage to 8 V peak-to-peak. The value of this capacitor is -HF. (Round off to 2 decimal places).
4) Consider the clamping circuit below, assume Vref=3 V and Vin=5sin(wt) ..Draw the output voltage waveform. Clearly mark the max and min of the voltage.. Vref
what is the relationship, if any, between the amplitude of the output waveform and the bias voltages?
Figure below shows a circuit for a pulse width modulator (PWM) amplifier. I. Describe how the circuit achieves low power dissipation 2. Describe with the aid of drawings the signal waveform shapes at points, A, B and C
Find the resonance point and the half-width of the speed versus frequency curve for the damped harmonic oscillator, under the action of a sinusoidal driving force. *It is all the data
(ii) What is IEEE519 standard? Explain the significance of the terms PCC, Isc and I used in this standard. Describe the maximum harmonics current distortion in % of I for individual harmonic order prescribed by this standard.
Find the following: DC gain, inductor current ripple and output voltage ripple: For DC-DC Buck converter: 1-Draw all circuits in all position 2-Sketch the transistor current waveform 3-Derive analytical expressions for the dc components of the capacitor voltages and inductor currents. 4-Derive analytical expressions for the peak ripple magnitudes of the input filter inductor current and capacitor voltage.
The term duty cycle refers to the amount of time a signal is complete cycle. A. off compared to the period of one B. on The output voltage of op-amp is positive saturation, when the voltage applied to the input is greater than the input. A. inverting B. noninverting A square wave that is 20V at its high state and OV when it is off will produce an average DC when its duty cycle is 75%. Formula: VOUT = Duty Cycle * Peak voltage voltage of A. 7.5V B. 10V C. 15V
6. Consider the electrical circuits shown in figure a.) and b.). For each circuit determine the transfer function C/2 C12 2R 2R (a) R (b)
4. Signal conditioning element basically takes the output of the sensing element and converts it into a form more suitable for further processing, usually in the form of a DC voltage, DC current or variable frequency AC voltage. The output of the sensing element is usually too small to operate an indicator or a recorder. Therefore, it is suitably processed and modified in the signal conditioning element so as to obtain the output in the desired form that is amplify the signal and filtering the unwanted signal. i. Describe the aliasing phenomenon. ii. Suggest a solution to minimize the effect of aliasing.
a.Derive the excitation equations b. Determine transition and output equations c. Derive the transition/output table and Draw the state diagram.