(b) You are given an μA741 op-amp chip with an open loop gain of 200,000, unity bandwidth of 1 MHz and short circuit output current of 25mA. With a +12 volt power supply and appropriate resistors: (1) (ii) Design an amplifier with a gain of +20, sketch your circuit labeling all components and values. What is the maximum input voltage possible without clipping and given this calculate the voltages and currents associated with each resistor including a load of 1k0 and state how much current the amplifier is sinking or sourcing? What is the bandwidth of your amplifier.

(b) You are given an μA741 op-amp chip with an open loop gain of 200,000, unity bandwidth of 1 MHz and short circuit output current of 25mA. With a +12 volt power supply and appropriate resistors: (1) (ii) Design an amplifier with a gain of +20, sketch your circuit labeling all components and values. What is the maximum input voltage possible without clipping and given this calculate the voltages and currents associated with each resistor including a load of 1k0 and state how much current the amplifier is sinking or sourcing? What is the bandwidth of your amplifier.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Construct the small signal model of the circuit shown below:
A appropriate op-amp circuit with a gain of +100 is required for the ultrasonic device. Create a two-stage non-inverting op-amp circuit with Av = 10 for each stage. Provide calculation procedures that complement the circuit design.
Figure QI shows the circuit diagram of a "Logarithmic Amplifier". In this circuit the feedback resistor of a normal inverting amplifier is replaced by a silicon diode. Since the current flowing through the diode increases exponentially with the voltage across the diode, the voltage across the diode will be proportional to the logarithm current flowing through it. Hence the output of the circuit is proportional to the logarithm of the input voltage. QI DI RIN Al Figure QI The current flowing through a diode is given by the Shock' y Diode Equat n: 1,=1, (e" =1) where , is the current flowing through the diode g is the charge on the electron (given at the back of the examination sheet) V, is the voltage across the diode K, is Boltzmann's constant (given at the back of the examination sheet) Tis room temperature (given at the back of the examination sheet) Given that /,> 1, an approximate expression for V, as a function of I, is Continued overleaf Page 2 of 9 QI (a) 0) Neglecting any input…
6. For common-source small-signal FETS, the output voltage is 180° phase shifted with respect to the Q 7. The operating cycle of a Class A amplifier is Q 8. The maximum efficiency of a Class B amplifier is Q 9. In analyzing op-amps, when the non-inverting input pin is at ground and the inverting input pin is also at 0 V for an AC signal, the technique is called as Q 10. is an op-amp application circuit which is useful in low pass filter circuits.
What is the DC gain of the given circuit above?
Design a collector-feedback circuit using with Vcc = 5 V, Ic = 10 mA, and VCE = 1.5 V.
2. One of the earliest uses of operational amplifiers (OPAMPS) is to perform mathematical operations on analog signals. Of the two OPAMP circuits shown below, one of them is known as an analog differentiator while the other an analog integrator. Analyse these circuits to discover why by finding an equation for their output VOUT in terms of their time-varying input VIN(t). (You may assume the OPAMPS are ideal.) VIN(t) RF Circuit A ☑ RF VOUT VIN(t) Circuit B VOUT
Introducion to Electronic Analysis and Design - CE05 To have a good amplifier Select one: a. The input resistance should be high b. the output resistance should be high c. the voltage gain should be equal to zero d. the current gain should be equal to zero Ssment CE255/EE255 (O1)- Dr. Mamoun Al-Mistar Jump to...
Since the sinusoidal input signal has a amplitude of 7 V and a frequency of 99 kHz in a voltage follower circuit (voltage follower:buffer), what must be the minimum slew rate of the operational amplifier so that the output can be seen without distortion in the signal?
What are circuits can used to design Class B amplifier ? explain the important features ? for each
Read the spec sheet for an AD797 op amp. What is the most interesting aspect of thiscomponents performance?
Determine the maximum theoretical efficiency of RC-coupled class-A amplifier as shown in Figure Q2(a). Show every detail of the calculation steps. Vcc Ice R1 RL C2 IB R2 IE Figure Q2(a)