Situation - The beam BC shown is supported by a quarter- -circułar are-AC having a radius of 5- m. The frame is pin- supported at A, B and C. The pins at A and B are in single shear while the pin at C is in double shear. Allowable shear stress of the pin is 120 MPa. w = 4 kN/m, P = 30 kN, a = 3 m. %3D IP а C. B R A Determine the minimum diameter (mm) of the pin at B. Determine the minimum diameter (mm) of the pin at C.

Situation - The beam BC shown is supported by a quarter- -circułar are-AC having a radius of 5- m. The frame is pin- supported at A, B and C. The pins at A and B are in single shear while the pin at C is in double shear. Allowable shear stress of the pin is 120 MPa. w = 4 kN/m, P = 30 kN, a = 3 m. %3D IP а C. B R A Determine the minimum diameter (mm) of the pin at B. Determine the minimum diameter (mm) of the pin at C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A linkage to an aircraft landing gear is shown. 0.1 m • The 40-kN force acting on the wheel has a line of action acting 15° from a vertical reference line, as shown, and that intersects point D, as shown. • Each pin has a diameter of 25 mm, and is in single shear. • Strut BC has a width of 38 mm (shown) and a thickness (into the page) of 12 mm. • Member ACD has a width of 35 mm and a thickness (into the page) of 10 mm. a. Determine the normal stress on by the points on a cross- section located halfway between B and C (in strut BC). b. Does every cross-section in strut BC feel the same normal stress? Why or why not? 40 KN c. Determine the average shear stress in pins A, B, and C. d. Determine the bearing stress between pin A and member ACD. e. If the plate that member ACD is connected to at pin A is 15 mm thick (into the page), determine the bearing stress between pin A and that plate. 0.4 m 15⁰ A B 38 mm 0.4 m 0.4 m
Two ropes are used to hoist a 610 Ib engine/transmission assembly as shown. The rope is anchored at C around the center part of the pin shown, causing the pin to experience a state of double shear. There is a frictionless pulley at A. The normal stress in the rope must not be allowed to exceed 12 ksi, and the shearing stress in the pin must not exceed 23 ksi. When the hoist is in the position given by: a = 41 in b = 13 ft c = 15 ft find the following: (a \& b) The forces carried in ropes AB and BC (c \& d) The necessary diameters of ropes AB and BC (e) The necessary diameter of the pin at C 2013Mchas (a) TAB = () Твс !! (c) dAB = (d) d BC %3! (e) d = %3D be sure to include units with your answers I3D
2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ } 2.5 ft -3 ft -5 ft 150 lb/ft Fx =
Current Attempt in Progress Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 11 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 9 mm in diameter. Assume a = 540 mm, b = 270 mm, h = 360 mm, and 0= 50%. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 120 MPa, determine the maximum load Pmax that can be supported by the structure. D Th B a C
Two ropes are used to hoist a 530 lb engine/transmission assembly as shown. The rope is anchored at C around the center part of the pin shown, causing the pin to experience a state of double shear. There is a frictionless pulley at A. The normal stress in the rope must not be allowed to exceed 15 ksi, and the shearing stress in the pin must not exceed 21 ksi. When the hoist is in the position given by: a = 44 in b = 11 ft c = 19 ft find the following: (a \& b) The forces carried in ropes AB and BC (c l& d) The necessary diameters of ropes AB and BC (e) The necessary diameter of the pin at C 2013 Michael Swanbom (a) TAB = (b) TBC = (c) dAB = (d) dBc = (e) d =
The structure shown consists of a single member ABCDE with a pin support at A and a roller support at E. Points B and D are at the midpoints of their respective segments. Determine the internal shear force acting on I which are located immediately to the left of C. Take N = 1 kN, O = 3 kN, and P = 4 kN.
Required information Link AB, of width b = 2 in. and thickness t= in., is used to support the end of a horizontal beam. The average normal stress in the link is -21 ksi and the average shearing stress in each of the two pins is 12 ksi. 4 NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the diameter d of the pins. The diameter d of the pins is in.
Provide information for constructing the shear diagram. The x origin is on the left at A and the support reactions are A, = 3 kip acting up, C, = 9 kip acting up and Mc = 60 kip-ft acting clockwise. A is a roller, B is a pin and Cis a fixed !! support. What happens to the shear diagram at x = 16 ft? 3 kip 15 kip/ft B 12 ft 4 ft 4 ft O Increase 1.5 kip O No change Increase 3 kip Decrease 9 kip Decrease 6 kip Increase 6 kip O Decrease 3 kip Increase 9 kip Decrease 1.5 kip
The following shaft is free at A and connected to a fixed support at C. The shaft has a solid circular cross section with radius equal to 25 mm. given the two external forces at section A: (a) Determine the internal loading components at section B. (b) Determine the combined shear stress at point P located on top of section B. (c) Determine the combined normal stress at point P.
The 40-mm diameter solid shaft ACBD is supported by two bearings at A and B. Due to the transmission of power to and from the shaft, the belts of the pulleys are subjected to the tension forces shown in the figure below. 1-Draw the moment and shear diagrams on the y z and y x planes 2-Determine the location and magnitude of the maximum bending (normal) stress. Hint draw the shaft cross section at that location and think of the associated stresses. 0.050 m 300 N 0.250 m 200 N 550 N 0.250 m 400 N 150m D 0.075 m
All the pins are in double shear, and they each have a diameter of 14 mm. The average shear stress in each pin CANNOT exceed 70 MPa. What is the max magnitude of P that the beam can support
Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear and have a diameter of 0.500 in. Assume L = 7.5 ft. If the average shear stress in the bolts cannot exceed 55 ksi, determine the maximum distributed load Wmax that can be supported by the structure. W (1) B Answer: Wmax kips/ft = L