The 40-mm diameter solid shaft ACBD is supported by two bearings at A and B. Due to the transmission of power to and from the shaft, the belts of the pulleys are subjected to the tension forces shown in the figure below. 1-Draw the moment and shear diagrams on the y z and y x planes 2-Determine the location and magnitude of the maximum bending (normal) stress. Hint draw the shaft cross-section at that location and think of the associated stresses.

The 40-mm diameter solid shaft ACBD is supported by two bearings at A and B. Due to the transmission of power to and from the shaft, the belts of the pulleys are subjected to the tension forces shown in the figure below. 1-Draw the moment and shear diagrams on the y z and y x planes 2-Determine the location and magnitude of the maximum bending (normal) stress. Hint draw the shaft cross-section at that location and think of the associated stresses.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.16P: For the thin nonprismatic steel pipe of constant thickness t and variable diameter d shown with...

See similar textbooks

Similar questions

Determine the resultant internal loadings acting on the cross section at B of the pipe shown. End A is subjected to a vertical force P and a horizontal force Q. Use P = 90 N and Q = 70 N. a. Determine the internal axial force (in N) in section B. b. Determine the internal shear force (in N) in section B. c. Determine the internal torque (in N-m) in section B. With FBD please thank you.
For the 80-mm shaft subjected to two concentrated forces shown, the journal bearings at A and B only support vertical forces. Address the following: (a) Construct a shear and moment diagrams for the shaft using the graphical method. (b) Determine the absolute maximum bending stress (highlight the location of maximum normal stress). 12 kN -0.5 m -0.4 m 20 kN 0.6 m
Determine the normal force, shear force, and moment at point C. Take that P = 8 kN and M = 33 kN m. (Figure 1) Figure M B . 1 of 1 -1.5 m 1.5 m 1.5 m-1.5 m-
Determine the maximum positive normal bending stress that occurs in member ABC of the engine crane given the following information: Engine weight = 1500 lb Member ABC height (vertical cross sectional dimension) = 7 in Member ABC width (horizontal cross sectional dimension) = 1 in Express your answer to the nearest whole psi value. In your work, draw the shear and moment diagram for member ABC. For the question above, determine the maximum shear stress in member ABC that occurs between points A and B. Express your answer using the nearest whole psi value.
Smooth journal bearings at A and B that only exert vertical reactions on the shaft as shown below support the shaft. Based on the loading and support conditions shown, address the following: (a) Sketch the shear and moment diagrams using the graphical method - label all significant conditions. (b) If d = 90 mm, determine the absolute maximum bending stress in the beam, and sketch the stress distribution acting over the cross section. A 3 m 12 kN/m B 1.5 m
Determine the internal normal force and shear force, and the bending moment in the beam at points C and D. Assume the support at B is a roller. Point C is located just to the right of the 8-kip load. For your explanation section, complete a FBD of the other side of the beam from the version you did to solve the problem. 8 kip 40 kip · ft A to to D B- 8 ft 8 ft- -8 ft
3) If the maximum torsional shear stress for the shown circular shaft is 4000 psi, the torsional shear stress at the given radial coordinate is------psi. A-3200 C-zero B-5000 D-4000 r=5in p=4in +
Problem 2. Consider a rod with radius c, subject to shear force V. Clearly show the Neutral Axis on the cross-sectional area. Determine the maximum shear stress from the shear formula t=VQ/(It) and identify where these maximum shear stresses occur; write magnitude in terms of V and c. Identify the section area and section area centroid used to calculate the maximum first area moment max What is the shear stress at points A У А where t=t, max and B? What is the shear stress at the centroid? What is the shear stress at points F and E at the top and bottom? By what factor is the maximum shear stress greater than the average shear stress acting over the cross-section.
Problem Statement Based on Problem 7-14 from the textbook. Determine the normal force, shear force, and moment at points F and E. w=60 lbs/ft a= 5 ft b=5.5 ft A -3 ft E 12 ft B a b 2 ft
The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. Take: d1 = 1 m, d2 =1 m, d3 = 1 m, d4 = 1.2 m, d5 = 1.4 m, F1 = 691 N/m, and F2 = 1,189 N. Determine the bending moment (Mc) acting on the cross section at C in N-m. Hint: consider the sign convention for internal loods. F1 В + di d2 d3 d4 ds F2
The simply supported joist is used in the construction of a floor for a building. In order to keep the floor low with respect to the sill beams C and D, the ends of the joists are notched as shown. If the allowable shear stress is tallow = 350 psi and the allowable bending stress is sallow = 1500 psi, determine the height h that will cause the beam to reach both allowable stresses at the same time. Also, what load P causes this to happen? Neglect the stressconcentration at the notch.
Specifications of the steel rod at B. Length=2 meters diameter= 25 mm E= 200 GPa Show complete solution 1. Draw the shear force and bending moment diagrams. 2. Determine the maximum flexural stress 3. Determine the stress in the steel rod at B