Situation #2: A properties: Width, b = 400 mm 415 MPa rectangular beam has the following Effective depth, d = 620 mm 22 MPa Tension bars, 10 pcs 28-mm-diameter Compression bars, 3 pcs 25-mm-diamter d' = 70 mm fy= = fc': Determine the design strength of the beam and the safe live load if the service dead load is 320 kN.m =

Situation #2: A properties: Width, b = 400 mm 415 MPa rectangular beam has the following Effective depth, d = 620 mm 22 MPa Tension bars, 10 pcs 28-mm-diameter Compression bars, 3 pcs 25-mm-diamter d' = 70 mm fy= = fc': Determine the design strength of the beam and the safe live load if the service dead load is 320 kN.m =

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.11.5P

See similar textbooks

Similar questions

Hw: Find the Sslope and defletion in the section CA-A) and the section cB-B) fur the beam Showwn. Given, I = 5*l-"m4 aued Es 205 G Pa. A 2 kulm Im 2.5 m Im A
A simply supported beam is subjected to a uniform service dead load of 15kN/m(including the weight of the beam), a uniform service live load of 30kN/m. the beam is 12 meters long and is laterally supported at the midspan, and A572 Gr.50 steel is used. Is W30x108 adequate? Assume Cb=1 by 4 d fore k h h Z S Ly 267 TH mm 19.3 757 13.8 min m 35.8 685.4 54.6 737.7 5670 x10^3 4900 x103 mm 60.8 x10 6 mm 2080 x10 3 8300 x10^9 mm www
For the beam below, determine the following, assume EI is constant. What is FEMAB in k-ft? -18 --96 Select the correct response: -69 2 k/ft 18 24ft
Grath fas A cantlever AB o erath lm carries a from klev. uniformly distributed load, wNm fe fired end A to the free end B. Te the cantilever Consista a horizontal thicknees lomm and with 120mm as shown in fhe below, plars plate4 figure calculate the total permiseiblé diafribte load,wif the meximum bending Stress is not exceeding 10OMH/mt. Ignore the grore te weight a the tlefe Im 120mm
Part 1 The simply supported beam below is initially designed to undertake a concentrated factored live load of 45 kips (215 kN). Assume that the beam is laterally supported and the self weight neglected. Use: A992 steel (Fy= 50 ksi or 345 MPa) E = 29 x 10® psi (200 GPa), the maximum allowable deflection Aall = L/360 45 kips 16 ft 16 ft 1/ Determine the most economical W shape beam required Part 2 The most economical selected beam from Part 1 ends up being subjected to a concentrated live load of 20 kip. Determine the corresponding maximum live load deflection. Part 3 Assuming that the beam will only be braced laterally at the supports and every quarter spam points (8ft from each support), verify whether the chosen cross section still checks under the live load of 20 kips only. If not, what are your design recommendations?
1. A steel column 10 m long is fabricated from a cover plate and C section arranged as shown. Determine the safe compressive load. Fy = 248 MPa, E= 200 GPa. Use AISC/NSCP Specs. 450 mm -cover plate 'I 12 mm y2 IP d2 10 m C 310 x 37 A = 4720 mm? d = 305 mm bf = 77 mm tf = 12.7 mm tw = 9.8 mm C 310 X 37 a) Both ends of column are fixed b) Both ends of column are hinged c) One end fixed, the other end hinged Use design values of k. tw d=305- Ix = 59.9x10° mm ly = 1.85x10° mm x = 17.1 mm x=17.1
2. The column shown in the figure is reinforced with 6 - 25mm diam steel with fy: = 415Mpa and f'c = 27Mpa a. Determine the nominal load pn when e = 200mm b. Determine the nominal load when e = 350mm C. 250 mm 65 mm 400mm 65 mm e CD Pn
500 mm 62.5 mm 375 mm 62.5 mm P. Determine the total required number of 20mm bars to be used in two end faces only for the 300mm x 500mm rectangular column shown to support the following loads: Pu = 800 kN Mu = 120 kN-m Use f'c = 20.7 MPa and fy = 413.7 MPa Use 1 ksi = 6.893 MPa %3D 300 mm O O O O
Compute the compressive strength of a WT 12x81 of A992 steel. The effective length with respect to the x-axis is 25 feet 7inches, the effective length with respect to the y axis is 20feet, and the effective length with respect to the z-axis is 20 feet WT12X81 A 23.9 t₁ 1.22 ly 221 d 12.5 K des 1.72 J 9.22 b₁ 13.0 y 2.70 Cw 43.8 tw 0.705 Ix 293
ure B 2m2 m C -2 m D 4 m 500 N 700 N 2 of 2 Part B Identify the zero-force members in the truss shown in (Figure 2). Check all that apply. 000 CD DE CG CF FG BC BG DF AG EF AB Submit Provide Feedback Request Answer
EYA 98 B/s docs.google.com/forms 100 Papertine J MA Papertine Papertine 45 - ls- das #2: For the Simply supa ted beam having the Sechin Shown and londed partially, Find: 1. Draw the bending moment diagram ? 2. Find the value of the maximum bendig moment Mmak 3. Find the value f the maximum bending stress Vmax ال لعة البطم رات المطع الو ضع المكل والحملة ۱. أسم الر البان لعن اوكماو : Mmax sls! e de i ană fic أوجه تعة أ على إ دإما کے ļ Umax KN/m - 20 Cm 4 1 m. 2 m. 1 m. Neutral 40 cm Axis Beam (AB) Beam Cross- Section ت إضافة ملف
How Determin # As for the beam show in figre (including self weight) (P=35 M²-i fy=420) well kN/m WL=24 K~/3 590 250 5m