SIMULINK Implementation 1. Using SIMU LINK, set up the negative feedback system of (6) above. Plot on one graph the error signal of the system for an input of Su(t) and K = 50, 500, 1000, and 5000. Repeat for inputs of 5tu(t) and 5e"u(t). Use simulation time not less than s0 seconds for all the simulations 2. Using SIMULINK, set up the negative feedback system of (7) above. Plot on one graph the error signal of the system for an input of Su(t) and K = 50, 500, 1000, and 5000. Repeat for inputs of Stu(t) and 5tu(t). Use simulation time not less than s0 seconds for all the simulations 3. Using Simulink, set up the negative feedback system of (8) above. Plot on one graph the error signal of the system for an input of Su(t) and K = 200, 400,800, and 1000. Repeat for inputs of 5tu(t) and 5t'u(t). Use simulation time not less than s0 seconds

Convert the NFA defined by 6(q0, a) = {qo, q1} 8(q1,b) = {q1, q2} 8(q2, a) = {q2} With initial state qo and final state q2 into an equivalent DFA

FACTS: In Module 3, you have learned about Op-Amps like Inverting and Non-Inverting Amplifier and many more, one of the topics in Module 3 is the Integrator and Differentiator. An operational amplifier (op-amp) integrator is an operational amplifier circuit that performs the mathematical operation of integration with respect to time-this means the output voltage is proportional to the input voltage integrated over time. A differentiator is an op amp-based circuit, whose output signal is proportional to the differentiation of the input signal. An op-amp differentiator is basically an inverting amplifier with a capacitor of suitable value at its input terminal. The electric potential of inverting terminal is also zero, as the opamp is ideal. QUESTION: Answer the ff. 1. What are the problems in an ordinary op-amp integrator? 2. Why op-amp integrator output is linear? 3. What are the problems in an ordinary op-amp differentiator? 4. What are the advantages of integrator and differentiator…

java   Compute a table representing the Knuth-Morris-Pratt failure function for the pattern string "cgtacgttcgtac". ​​​​​​​

Write a MATLAB program to find the autocorrelation of the signal given below but you have to use the conv() function to find the autocorrelation. The use of the corr() function will lead to the rejection of the assignment. Signal: x (n) = {0,1,4,–3} %3D

Give your own non-software example of the Mediator pattern.

A sequential circuit has one input X and four outputs Z₁ Z₂ Z3 Z4. Z1 Z2 Z3 Z4 represents the gray code encoded number equal to the number of pairs of adjacent 1's that have been received as inputs. Use the gray code that is on page 22 of the textbook. For example, if the circuit had received 7 pairs of 1's as inputs, Z₁ Z2 Z3 Z4 = 1011. In addition, the circuit resets when the circuit receives 5 pairs of 1's. Find a Moore state graph and table for the circuit. Examples Input sequence: Output sequences: X = 1 0 1 1 1 0 0 1 1 0 1 1 0 1 0 1 1 10 Z₁ = 0 0 0 0 0 0000000000100 Z₂ 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 Z3 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 - Z4 = 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 X 11111111 Input sequence: Output sequences: Z₁ = 0 0 0 0 0 100 Z2 0 0 0 0 1 100 = Z3 = 0 0 1 1 1 1 0 0 Z4 0 1 1 0 0 0 0 1 =

Design a 4:1 MUX in multiple ways: a) Using basic gates b) Using tri-state logic c) Using 2:1 MUXes as building blocks as much as possible For each design, write a Verilog implementation and simulate the behavior. Your testbench should exercise all possible combinations of the inputs and selection values.

Consider the circuit diagram on the right hand side. Determine a NOR only 4. y representation of this circuit using the x' graphical method in the lecture. Show your steps clearly. D y z'

Implement the TRUTH TABLE of the following state machine and DRAW the SCHEMATIC CIRCUIT