Shown below is a toggle clamp that exerts only a vertical clamping force on the wood block at A. Determine the clamping force at A knowing that the force applied to the handle is F = 460 N, and the handle is L = 300 mm long. Enter the magnitude of the clamping force below. Express your answer in N to the nearest whole N. Note that the force F is perpendicular to the handle. -235 mm- 30 mm 30 mm 70 mm E L Your written solution must include must include all necessary FBDs and calculations needed to determine the force clamping force at A, the force in member BE, and the forces exerted on member ACD by the pins at C and D.

Shown below is a toggle clamp that exerts only a vertical clamping force on the wood block at A. Determine the clamping force at A knowing that the force applied to the handle is F = 460 N, and the handle is L = 300 mm long. Enter the magnitude of the clamping force below. Express your answer in N to the nearest whole N. Note that the force F is perpendicular to the handle. -235 mm- 30 mm 30 mm 70 mm E L Your written solution must include must include all necessary FBDs and calculations needed to determine the force clamping force at A, the force in member BE, and the forces exerted on member ACD by the pins at C and D.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.15P: The structure is supported by a pin at C and a cable attached to A. The cable runs over the small...

See similar textbooks

Similar questions

20 F- 10 N 250 mm The 10-N force is applied to the handle of the hy- draulic control valve as shown. Calculate the mo- | 60/ 37.5 mm ment of this force about point O. find out th recultent omont of tuo forooc choun in Fig
The figure below shows a toggle clamp. If force F is exerted as shown, determine the vertical clamping force at E. a/2 + 1.5 a m E 1.5 a 60° C a/2 a/2
2-13 The force acting on the gear tooth is F 20 tb. Resolve this force into two components acting along the lines aa and bb.
Determine the Resultant Force, its magnitude and direction of the given co-planar ,Space tensile force cables as shown in the diagram below. AB = 120 LBS; AC = 250 LBS & AC = 90 LBS. Show fbd, and a complete solution
Homework 2-9 IE the resultant force acting on the support is to be 1200 Ih directed horizontally to the right, determine the force Fin rope A and the corresponding angle e 2-IN The force acting on the gear tooth is F= 20 h Resolve this force into two components acting along the lines ar and M 2-14 The component of force F acing along ine a is required to be 30 . Determmine the magnitude of F and its component along line b. 900 b Peu, 2-9 2-10 Determine the magnitude of the resultant force and its dircction, mcasured countendockwise from the positive aNiN wan Probs. 2-MA 2-15. Force Facts on the trame such that its component acting along member ABis 650 th directed fromB towards A. and the component acting along member BC is S00 Ih directed from Btowards C. Determime the magnitude of Fand its direction e. Set a r. Prah. 2-e 2-11. The plate is suhjected to the two forces at A and as ahewn. If- 60. determine the magnitude of the resultant of these two forces and its direction measured…
Determine the value of P acting to the left that is required to pull the wedge out from under the 40-kN block. 40 kN 60° P 10°
1. Determine the magnitude and direction with respect to the +x axis on the reaction at A and at C. Note that the body is supported by pin at A and a roller at C. The body's weight is negligible. A 2.4 kN-m 400 40° 200 250- Dimensions in mm -300- B 3 kN
with the following modifications: Replace the vertical 6kN at point B with a horizontal force 6kN acting to the right at the same point.
3. The rectangular block is to be pulled out of the ground using two strings A and B. String A is subjected to a force of 600 lb and is directed 60 degrees with the +x- axis. If the net force acting on the block is to be 1200 Ib, vertically upward, solve for the force T in string B and its direction angle 0. 600 Ib 60°
An engineer developed the following solution to the following problem. Verify his calculations. Is the given final answer "true" or "false"? Two forces F₁ and F2 act on the screw eye. If their lines of action are at an angle apart and the magnitude of each force is F₁ = F₂ = F, determine the magnitude of the resultant force FR and the angle between FR and F₁.
2-38. The three forces are applied to the bracket. Determine the range of values for the magnitude of force P so that the resultant of the three forces does not exceed 2400 N. Problem 2-38 800 N 3000 N 90% 60° X D
200 400 B 200 N m E D 200 F Dimensions in mm Determine the magnitude of the force (in N) of the x-component of the internal pin at D.