Shown below is a section from the datasheet of 74LS32, a quad 2-input OR chip. What is the noise margin high (in V) of this chip? Limits Symbol Parameter Min Typ Max Unit VIH Input HIGH Voltage 2.0 V VIL Input LOW Voltage 0.8 VIK Input Clamp Diode Voltage -0.65 -1.5 V V VOH Output HIGH Voltage 3.5 V V VOL Output LOW Voltage 0.35 0.5 V 20 μA IH Input HIGH Current 0.1 mA IIL Input LOW Current -0.4 mA los Short Circuit Current (Note 1) -100 mA Power Supply Current Total, Output HIGH 6.2 Icc mA Total, Output LOW 9.8 74 74 74 2.7 -20

Shown below is a section from the datasheet of 74LS32, a quad 2-input OR chip. What is the noise margin high (in V) of this chip? Limits Symbol Parameter Min Typ Max Unit VIH Input HIGH Voltage 2.0 V VIL Input LOW Voltage 0.8 VIK Input Clamp Diode Voltage -0.65 -1.5 V V VOH Output HIGH Voltage 3.5 V V VOL Output LOW Voltage 0.35 0.5 V 20 μA IH Input HIGH Current 0.1 mA IIL Input LOW Current -0.4 mA los Short Circuit Current (Note 1) -100 mA Power Supply Current Total, Output HIGH 6.2 Icc mA Total, Output LOW 9.8 74 74 74 2.7 -20

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For Full Wave Bridge Rectifier Ripple Factot = 19 % , and Vdc= 9 Volt. Find Vrms. . .volt and Vr(p-p). .volt. After use ( C- Filter) and use Silicon diode 0.171 , 0.5923 171, 5923 1.71m , 5.923m 1.71 , 5.923 Not all above O
Q4) If fr is the frequency of the fundamental component of the output ripple, then for full bridge rectifier, the output frequency fo in respect to input frequency fi is Ofr=fo=2fi Ob.fr=fo%3D3fi Ofr=fo=D4fi Ofr=fo=fi
Example Full wave rectifier)) for the signal shown plot the amplitude specturm -T=0.4 for 2.6M²/ 5.41 weez fo -5T redbr ~0.4 -0.2 XCD) Vm 0.2 0.4
The arrow on the symbol of MOSFET indicates O a. that it is a N-channel MOSFET O b. the direction of conventional current flow O c. that it is a P-channel MOSFET O d. the direction of electrons
uo A:EV * ll. pluli ► b89f3244-f736-4021-901... PI EXPlain The effect of increasing The filter Capacitance on The outfut Voltage in The haif - wave rectifier and filber Circuit ? CS Scanned with CamScanner
(2) In the adjacent circuit, the input signal Vin = F15V is a square wave. Draw the output signal as a function of time on both Vin ends of: (a)- load resistance. (b) Di-zener Vz=6V In terms of behavior, the value of the output voltage is fixed on the drawing, bearing in mind that the diode is made of
8 UTM Figure B.1 shows a diode circuit and its DC load line analysis. Based on the SUT information obtained UT UT I kQ + VpQ- 3 UTM UTM Vs 3 500 2 UTM & UM TM &UTM UTM UTM &UTM 5 UTM Figure B.1 UTM & U UTM VD (V) 0.72 UTM i UTM UTM
The reverse recovery time of diode is trr = 3 s and the rate off all of the diode current is di/dt = 30 A/s. The storage charge current QRR is?
Design the Clipper-Clamper circuit to perform the output waveform shown in figure below. GaAs Diode GaAs Diode Vo f=1 kHz. 3 V + -3V Clipper Clamper -13 V -10 V
The positive peak value of output waveform for the given circuit diagram is. Bias voltage is 2 V, Diode is germanium) (VPP of input is 18 V, V VouT
Negative Peak Clipper with bias circuit uses a germanium diode, with an input peak to peak voltage V=20 V and bias voltage V 2.7 v. a) What is the function of the circuit b) Draw the circuit diagram. c) Draw the input and output waveforms. Input Output
Question 3 Consider the following cirucit: in + V1 R1 5 PULSE (0 2 1 1 1 1) (Note again the unrealistic diode characteristics.) The input is a ramp: 2.0V- 1.6V- 1.2V- 0.8V- 0.4V- 0.0V- 0.0s 0.2s 0.4s 0.6s 0.8s out .tran 2 .model diode D(Ron=5 Vfwd=1 Roff=1G) V(in) D1 diode 1.0s 1.2s 1.4s 1.6s 1.8s 2.0s The output voltage is similar to the input voltage, except that it breaks at a certain voltage and reaches a different final value. Find the break voltage and the final value of the output.