PLEASE SOLVE THE QUESTION ATTACHED WITH STEP BY STEP SOLUTION.THANK YOU. The shunt admittance and series impedance of a long transmission line are givenwith respect to length as follows:y=j3.5x10-6S/kmz = (0.1 + j0.5)Q/kmThe length of the transmission line is 400km. It wheels 150MW at 220kV and 0.85pf lagging. Calculate the following:a) the A and B constants of the transmission line. [5,3]

A Long transmission line's Characteristic Impedance is given by root of ratio of series impedance…

The shunt admittance and series impedance of a long transmission line are given with respect to length as follows: y =j3.5x10-6S/km z=(0.1 + j0.5)/km The length of the transmission line is 400km. It wheels 150MW at 220kV and 0.85 pf lagging. Calculate the following: a) the A and B constants of the transmission line. [5,3]

The shunt admittance and series impedance of a long transmission line are given with respect to length as follows: y =j3.5x10-6S/km z=(0.1 + j0.5)/km The length of the transmission line is 400km. It wheels 150MW at 220kV and 0.85 pf lagging. Calculate the following: a) the A and B constants of the transmission line. [5,3]

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.46P

See similar textbooks

Similar questions

Which of the following parameter/s is represented as connected in shunt in the equivalent circuit for Transmission Lines? O A. RESISTANCE WITH THE INDUCTANCE O B. CONDUCTANCE ONLY OC. CONDUCTANCE AND CAPACITANCE O D. CAPACITANCE ONLY
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
A single-phase transmission line consisting of two conductors, the radius of each conductor is 0.4 cm, the distance between the conductors is three and half meters and the height above ground is eight 1-The capacitance in uF/km without effect of ground is 2-The capacitance in pF/km with effect of ground is
The Power transfer capability of transmission line is most affected by: it) shunt conductance b) capacitance c) Resistance. d) inductance
Q2: A single-phase transmission line consisting of two conductors, the radius of each conductor is 0.4 cm, the distance between the conductors is three and half meters and the height above ground is eight meter. The capacitance in µF/km without effect -1 of ground is إجابتك The capacitance in µF/km with effect of -2 ground is
A 5 km long, 3-phase 34.5 kV line has a horizontal configuration of 4 ft. spacing. The conductor is 336.4 ACSR with GMR of 0.0244. What is the inductance of the line? * A. 7.63 mH B. 4.76 mH C. 5.33 mH D. 6.49 mH
consider a transmission line with zl=3.346+j77.299 ohm assume that sb=100mva and vb=735kv find the per unit impedance convert the impedance using a new base of 200 mva and 345 kv
A single-phase transmission line consisting of two conductors, the radius of each conductor is 0.4 cm, the distance between the conductors is three and half meters and the height above ground is eight meter. Determine 1)The capacitance in uF/km without effect of ground 2)The capacitance in uF/km with effect of ground
Paragraph Styles The power factor must be close to in the transmission lines will be reduced To insure that losses D(Ctrl) -
2. A three-phase transmission line has parameters Xc-6 k 2, R-3.25 2 and X₁-25 92, and delivers 300 MW to a load with both ends of the line at 230 kV. Draw a pi equivalent per-phase circuit of the line. On a per-phase basis, calculate the active power delivered to the load, the reactive power of the line and the active power delivered by the source. Based on these calculations can the equivalent circuit be simplified further?
Give example problems for impedances and admittance.
1) A 60-Hz, ...-km, three-phase overhead transmission line has a series impedance z = 0.8431L79.04 ohm/km and a shunt admittance y = 5.105 × 106 L90 S/km. The load at the receiving end is 125 MW at unity power factor and at 215 KVLL. Determine the voltage, current, real and reactive power at the sending end and the percent voltage regulation of the line for nominal pi network. (Please determine the length of the transmission line within the specified limits: 150-220 km. By considering the length value you determined yourself, solve the question.)