SHOW THE GIVEN , REQD. AND COMPLETE SOLUTION The acceleration of a car is given by a = [ (3t^3 + 4t)i + 6tj + (8t – 5)k ] m/s^2. Determine the magnitude of its velocity when t = 3s. When t = 0 s, vx = 2 m/s, vy = 3 m/s and vz = 5 m/s

SHOW THE GIVEN , REQD. AND COMPLETE SOLUTION The acceleration of a car is given by a = [ (3t^3 + 4t)i + 6tj + (8t – 5)k ] m/s^2. Determine the magnitude of its velocity when t = 3s. When t = 0 s, vx = 2 m/s, vy = 3 m/s and vz = 5 m/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The tank of liquid in the figure accelerates to the right with the fluid in rigid body motion. Assume x = 44.1 cm and y = 106.5 cm Compute ax in m/s^2
Dynamics of Rigid Bodies
The blade on the horizontal-axis windmill shown in (Figure 1) is turning with an angular velocity of wo = 2 rad/s. It is given an angular acceleration of ac = 0.4 rad/s². Figure 15 ft 1 of 1 > Part A Determine the angular velocity of point P on the tip of the blade when t = 4 s. Express your answer in radians per second to three significant figures. wp= 2.68 195| ΑΣΦ. 41 Submit Previous Answers Request Answer Part B vec X Incorrect; Try Again; 4 attempts remaining ap = 2 ? Determine the magnitude of acceleration of point P on the tip of the blade when t = 4 s. Express your answer in feet per square second to three significant figures. IVE ΑΣΦ ↓↑ vec …..... www rad/s ? ft/s²
Question 21 3.5 m A C 5.5 m 0.2 m X B D G A Time left 0:58:42 In the figure above, the jib crane is supported by a pin at C and rod AB. Knowing that x = 5.7 m, and the load D has a mass of 3000 kg, with its center of mass located at G, you are required to explain your answers by your own words and A) Draw the free body diagram (FBD) [ B) Determine the reactions at the pin C C) Determine the force developed in rod AB D) Check the equilibrium of the system by determining the sum of the moments of all forces about point B 1.
1028. The motion of a particle is governed by the relation a = 4 P, where a is in feet per second' and t is in seconds. When t is zero, v Find the values of v and s when t 2 ft per sec and 4 ft. 2 sec.
Q1 A pendulum is modelled by a mass that is attached to a weightless rigid rod. According to Newton's second law, as the pendulum swings back and forth, the sum of the forces that are acting on the mass equals the mass times acceleration. The equilibrium equation in the tangential direction as: EF, -CL do dt -mg sin0 = mL Ld²o di² Where angle of the pendulum (with respect to the vertical axis, as shown in the figure) c=0.16(N-s)/m is the damping coefficient, m=0.5kg is the mass, L-1.2m is the length, and g-9.81m/s² is the acceleration due to gravity. The pendulum is initially displaced such that 0-90°, and then at t=0 it released from rest, = 0 (zero initial velocity). Determine the angle of the pendulum at 0.1 second using Runge-Kutta 2nd Order Method (Heun's method ) and step size (h=0.02). de dt 1-1-0 D 0 ។ K²₂² = f(tish, Off²h, 2; thks")
Part A Determine the magnitude of the particle's velocity when t = 4 s Express your answer to three significant figures and include the appropriate units. Part B Determine the magnitude of the particle's acceleration when t = 4 s Express your answer to three significant figures and include the appropriate units.
The rotor of a gas turbine is rotating at a speed of 6900 rpm when the turbine is shut down. It is observed that 4 min is required for the rotor to coast to rest. Assuming uniformly accelerated motion, determine (a) the angular acceleration, (b) the number of revolutions that the rotor executes before coming to rest. O alpha = -1625 rev s^-2; theta = 4600 rev O alpha = -1725 rev s^-2; theta = 13800 rev O alpha = -1825 rev s^-2; theta = 41400 rev
The figure shown is on a fixed frictionless axle. It has a moment of inertia of 1 = 50 kg-m². The forces acting on the object are F₁ = 100 N, F₂ = 200 N, and F3 = 250 N acting at different radii R₁ =60 cm, R₂ = 42 cm, and R3 = 28 cm. Determine the angular acceleration of the object. F F2 R₂ R F3
Calculate the r- and θ-components of acceleration.Answers: ar = m/s2 aθ = m/s2
Question 2 - Deflections - Determine the maximum upward and downward deflection and the rotation of the support on the left side of the beam shown in Figure 2. (F 4kN; L = 8m) a) Use a second order differential equation. b) Use the moment area theorems to verify your answers. L/4 L/4 L14 L/4 R, R2 Figure 2
The particle of mass m = 3.1 kg is attached to the light rigid rod of length L = 1.50 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity 0= w = 2.1 rad/s. Determine the force T in the rod when 0 = 26°. The force T is positive if in tension, negative if in compression. Part 1 Answers: ar = Calculate the r- and 8-components of acceleration. i L ae = i 0 8 m m m/s² m/s² e