Show your complete solution. Mang Inasal is working on a 300-mm solid shaft in his machine shop. Heplans to subject the said shaft on a loading condition as shown in thefigure. If the shearing stress on the shaft is limited to 60,000 kPa and theangle of rotation at the free end is not to exceed 1/45 pi radian, howmuch diameter should be removed from the material using the lathe'sturning operation in order to attain the minimum diameter in which theshaft can work with the said loading condition.750 Nm2.5 m2.5 m 1200 Nm

Answered: Image /qna-images/answer/27f0bc03-ddd6-47e3-9de2-db3cb988b87d.jpg

Answered: shop plans to subject the said shaft on…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a sand casting a steel rectangular plate with dimensions 80mm x 120mm x 20mm. Calculate shrinkage and draft allowance. And draw the designed pattern. Assume shrinkage of material as 0.1% for 12 inch, pattern material is wood and assume suitable draft angles
Solid modeling is a technique utilised by designers to enhance the three-dimensional and organic appearance of their works beyond what can be achieved through the mere assembly of lines. Explain?
100 mm diameter of a shell and a height of shell is 100 mm with the corner radius of 0.4 mm is to be produced by cup drawing , calculate the required blank diameter?
Heat treatment is the controlled heating and cooling of metals to alter their physical and mechanical properties without changing the product shape. When performing the cooling step of the tempering process, knife makers have used material such as clay to cover portions of the blade to slow the cooling rate of the covered steel. Why may this technique be beneficial for making a sword which holds a sharp edge while remaining flexible enough to withstand the forces subjected to it in battle?
A machinist was tasked to insert an aluminum piston into a steel cylinder. The inside diameters of the cylinder and of the piston are 0.500 m and 0.4998 m, respectively, at 25OC. To what temperature must they be heated to obtain a perfect fit?
Q2 (a) A sliding door rail as shown in Figure 2.1, is to be produced using steel as the raw material. If direct extrusion is to be used, at what temperature range (degree Celsius) and extrusion pressure range (MPa) the process should be carried out? Figure 2.1 A sliding door rail
How can you tell if a metal part is forged or cast. Describe the properties you would have investigated.
An aluminum oxide cutting tool will be produced. Would you produce it by casting? If you don't agree, please explain your reasoning and suggest a production method.
Explain what is the effective-slenderness ratio?
"Your boss requests a recommendation on which process to use to make fillet welds on stainless steel rail tank cars with this material. Your heart beating fast, you respond. " A: Use HYPERFILL®. The cooling rate is acceptable for this material and productivity gains are important given the large size of the product. B: "Use HYPERFILL®, for the same reasons as (A), BUT we need to change materials to a low carbon stainless steel (e.g. 304L) or we will get corrosion failure in the HAZ." C: "Use GMAW-P. For this material, this heat input is best. " D: "Use GMAW-P, for the same reasons as (C), but we need to change materials to a low carbon stainless steel (e.g. 304L) or we will get corrosion failure in the FZ."
Coupling will be used in the drive mechanism of the roles used in the Continuous Casting plant. The moment to be transmitted is high, the transmission distance is about 1500 mm, and there are fluctuations in the bending direction. Which type of coupling is best suited to absorb these fluctuations? Explain broadly the features of this coupling. Draw it schematically and explain the working principle.
Suggest three alternative materials that could be used to produce the desired wrench? Construct a comparison table to explain the advantages and disadvantages of each one? Cite appropriate references. Which of your alternative would you recommend to your supervisor?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS