Answered: Select a material for a non-lubricated…

Engineering

Mechanical Engineering

Select a material for a non-lubricated 25 pound block on a 30 degree steel incline to prevent sliding.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: *3-44. Determine the magnitudes of F₁, F2, and F3 for equilibrium of the particle.

Q: 1. Calculate the stress developed (in Pa) for the following structural members that are each…

A: Since you have asked multiple questions in a single request, we would be answering only the first…

Q: Given a spring with 2.032 mm wire diameter, oil tempered, 8 active coils, OD is 8.5 mm. Determine…

A: Given Wire diameter = 2.032 mm8 active coilsOuter diamter = 8.5mmStress =820MPaG=83GPa To-Determine:…

Q: Given a spring with 2.032 mm wire diameter, oil tempered, 8 active coils, OD i 8.5 mm. Determine the…

A: To Find : The free lenght Given : The wire diameter is The number of acive coils is The outer…

Q: A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric…

A: Given: Su = 345 MPa Load, P = 13 kN

Q: A Drive Shaft for a milling machine transmits 30 horsepower at a speed of 500 RPM. Compute the…

A: A Drive Shaft for a milling machine transmits P = 30 horsepower = 30 × 746 Watts, at a speed of N =…

Q: clearly

Q: 11. A rear flange mounted cylinder extends 14 in. under a load of 10,000 Ibf. What size cylinder rod…

A: Given Mass, m = 10000 lbf = 4535 kg Extension, h = 14 in…

Q: Find the force generated by the deltoid (right arm) if: His arm length (d) is: 0.84 m The COG of the…

A: Arm Length d=0.84mCOG=37%Wa=7.9NWw=126NAngle=90°Insertion=0.17mAngle for line of pull=11°…

Q: A steel wheel of 800mm diameter on a horizontal steel rail. It carries a load of 60ON. The…

A: We have to calculate rolling force

Q: end of the left rod and its pin support at C. After attachment, the strain in the left rod is 1.5 x…

Q: 1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the…

Q: Choose TWO (2) fit-up techniques that are required for preventing the excessive distortion occurred…

A: Solution: Two fit-up techniques that are required for preventing the excessive distortion occurred…

Q: If the length of a column is doubled, the critical load becomes ?

Q: If a cylinder had an internal diameter of 2 in and operates at a pressure of 300 psig, calculate the…

A: Write the expression to obtain the area.

Q: Given the following specifications of a standard fink truss: Cross Section of all the Truss Members:…

Q: The machine element shown is fabricated from steel. Determine the MMOI of the assembly with respect…

A: ρsteel = 8050 Kg/m³

Q: In a set of pulleys, 3 in the top, 2 in the bottom, it is required to lift a load. If 23% of the…

Q: 1- Design and sketch the form for 7.5 ft high and 1 ft thick wall using 5/8" B-B plyform Class I (4…

A: Given:- h=7.5 ftt=1 ft5/8" B-B plyform Class I (4 ft x 8 ft sheets)2 x 4 s4s Douglas Fir Larch No.2…

Q: Situation 5. Determine the member forces CD and GF using any method. Indicate if (T) or (C). 2 kN…

A: Given: P1 = 2 KN P2 = 1.5 KN To find: FCD and FGF

Q: 2. A steel strut, 40 mm diameter, is turned down to 20 mm diameter for one-half its length.…

Q: a) If a block is on a horizontal table with a horizontal force, sketch two FBD's of the block for if…

A: When a horizontal force is applied on the block on horizontal table, Initially the friction force…

Q: A 2-in.-diameter round steel rod 10 ft long is subjected toa tensile force of 60 kips. How much will…

A: Given Data⇒Diameter of round steeld=2 inLength of round steelL=10 ft=120 inTensile ForceF=60…

Q: ructural support for a machine will be subjected to a static tensile load of 16.0 kN.Specify…

Q: 3. In the given 15.0 meter slab and inclined 10°with the horizontal, the ends are resting on…

Q: A hydraulic cylinder with 15 mm diameter pushes a heavy tool during the outward stroke, placing a…

A: Given:To find:The mean stress.

Q: Determine the required length of a square key if the key and shaft are to be of the same material…

A: Required , length of a square key if the key and shaft are to be of the same material and of equal…

Q: Design a turnbuckle subjected to a load of 50 kN with permissible stresses are in 166.67 Mpa in…

A: Given Data P=50kN σt=166.67MPaτ=83.33MPaσc=166.67MPa

Q: What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of…

Q: A steel wheel of 900mm diameter on a horizontal steel rail. It carries a load of 50ON. The…

A: GIVEN DATA - W=500N D=900mm SO R=450mm μ=0.1 WE HAVE TO FIND VALUE OF FORCE

Q: A turning tool 15 in. long is subjected to torsion of 35,000 in-lbs. Compute the diameter of the…

A: Given Data- L=15in T=35000 in-lbs Angular deflection=1/64in G=6*10^6 psi Shear stress=3000 psi

Q: A steel drum of a lifting machine has a mass of 25 kg, 2.4 m in diameter and 0.20 adius of gyration.…

Q: Determine all support and pin forces for the frames listed below. Include force summary table for…

Q: b- 10 mm diameter of Brinall hardness ball when the load 500 kgr and HB= 300 determined the diameter…

A: Given: Diameter of the ball=10mmBrinall hardness =300Loading=500kg.f

Q: A stainless steel cortical screw is to carry a maximum load of 2000 Ibs. a. What is the minimum…

A: Given:Pmax=2000 lb

Q: Q2) design a nut, and screw jack (normal series) manufactured from a high grad materials and…

Q: A 1000 Ibs TTTTT t A horizontal cable exerts a force of 399.971 pounds while holding a boom into…

Q: The total length of a first class lever is 9.0 ft. This is used to move a load of 390 lbs, as…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Select a material for a non-lubricated 25 pound block on a 30 degree steel incline to prevent sliding.
O Aluminum-Bronze
O Steel
Brass
O Cast Iron

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: To choose

VIEW

Step 2: Explanation

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

STATICS OF RIGID BODIES RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES.
Defien the formula used to Determine the flexural rigidity D of the mat ?
Can someone please help me to solve the following problem showing all work neatly hand written. Following ALL DIRECTIONS as asked PLEASE AND THANK YOU!!!
1. You are to design an axially loaded member that is to carry a load of 5,000 lb. The member is to be made of ASTM A36 steel and have a total length of 24 in. Due to the design requirements the maximum allowable elongation of this member under the stated load is 0.025 in. Find the smallest allowable diameter of the member. a. Given: PL where ô is member elongation, P is axial load, L is initial member length, E is the material's Modulus of Elasticity, EA and A is the member's cross section area E136 = 29*10° psi (Beer, 746)
I need the answer of question attached. Please show all the work. Thanks!
10.86 QUESTION 5 A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, Su=345 MPa) for the C-frame material. Calculate the location of centroidal axis upto 2 digits after decimal point in mm? 18 mm 38 mm 13 kN 25 mm 10 mm -90 mm At 10 mm QUESTION 6 Conrider the rireular hant rod with dinmater 20 mm The fraa and of +ha hand is euhiactad to loads as choun in the fimura Click Save and Submit to save and submit. Click Save All Answers to save all answers. Save All An to search
Solve the problem. 1. You are using a wheel and axle as a simple machine. You applied a force of 30 lb to the rim of the wheel so that it can lift a load of 240 lb. The diameters of the wheel
A structural support for a machine will be subjected to a static tensile load of 16.0 kN. It is planned to fabricate the support from a square rod made from SAE 1020 hot-rolled steel. Specify suitable dimensions for the cross section of the rod.
STATICS OF RIGID BODIES NEED ASAP RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES. NOTE: THE TOLERANCE IS 1 IN THE THIRD SIGNIFICANT DIGIT.
Please show all work thanks
Solve the following problem (NOTE: Use any reasonable DATA not given in the problem.)
* Problem-based learning - Acquire enhanced problem-solving skills using critical thinking Two shaft 40 mm of diameter are connected by a flanged coupling. The flanges are fitted with 8 bolts on 140 mm bolt circle. The shafts transmit a torque of 900 N-m at 350 r.p.m. For the safe stresses mentioned below, calculate 1. diameter of bolts ; 2. thickness of flanges ; 3. key dimensions ; 4. hub length; and 5. power transmitted. Safe shear stress for shaft material = 63 MPa Safe stress for bolt material = 56 MPa Safe stress for cast iron coupling = 10 MPa Safe stress for key material = 46 MPa A belt 100 mm wide and 10 mm thick is transmitting power at 1000 rev/min while the large pulley rotates , The larger pulley diameter is 1 .8 times the smaller pulley which having 250 mm diameter. Calculate the maximum power that can be transmitted. When the distance between the two pulleys are 4 m