A structural support for a machine will be subjected to a static tensile load of 16.0 kN. It is planned to fabricate the support from a square rod made from SAE 1020 hot-rolled steel. Specify suitable dimensions for the cross section of the rod.

A structural support for a machine will be subjected to a static tensile load of 16.0 kN. It is planned to fabricate the support from a square rod made from SAE 1020 hot-rolled steel. Specify suitable dimensions for the cross section of the rod.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.5P: Solve Problem 11.3-3 for a W 10 × 45 steel column having a length L = 28 ft.

See similar textbooks

Related questions

Q: A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric…

A: Given: Su = 345 MPa Load, P = 13 kN

Q: Problem 4 only, solve carefully, include the units in every step and draw the diagram. Thanks! A…

Q: Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint.…

Q: Calculate the percentage error in finding the bulking load if the equivalent length for the freely…

A: Strut is a member or bar (in any position), which is subjected to axial compressive load. Column is…

Q: What are the advantages or disadvantages of eccentric loading of a column? Explain briefly.

A: Given Eccentric loading of a column To find Advantage of eccentric loading of a column Disadvantage…

Q: An aluminum bar having a cross-sectional area of 0.5 in? carries the axial loads applied at the…

A: Given Data Area, A=0.5 in2. E=10(106) psi

Q: It is intended to fit a 1 m long titanium Ti-6A1-4V rod with a diameter of 15 mm inside a rigid…

A: Given:For titanium Ti-6A1-4V material,modulus of elasticity, E=110 GPaPoission's ratio, ϑ=0.3initial…

Q: Determine the critical load for a pinned-end col- umn made of a circular bar of SAE 1020 hot-rolled…

A: Given Length, L = 800 mm Diameter, d = 20 mm For SAE1020 Young's modulus, E = 205 GPa Find…

Q: A structural support for a machine is subjected to a static compression load of 20 kN. The support…

Q: The figure shows a welded-arm. The arm is welded using ! normal yield strength of 393MPa. If the…

A: Given data: The given weld size from the figure is The radius of the weld is

Q: Determine the maximum inside diameter, din, permitted for a hollow driveshaft if the outside…

Q: Compute the design factor in the middle portion only of the rod AC if the steady vertical force on…

Q: An aluminum rod, made from alloy 6061-T6, is made in the form of a hollow square tube, 2.25 in…

Q: Assuming a minimum design factor = 2.00, Design the bolted cover of pressure vessel; determine the…

Q: Calculate the critical load of a strut which is made of a bar circular in section ich is pin-jointed…

A: GIVEN data L = 5m δ =10mmw = 80N

Q: A 38.1 mm pulley is fastened to a 120 mm shaft by means of square key with 150 mm long. What force…

A: A sheave or tiny wheel with a grooved rim and with or without the block in which it travels is used…

Q: Discuss what is meant by buckling for a long slender bar. Discuss the difference of a pin supported…

A: When vertical long slender bars are subjected to axial compressive loads they bend sideways or…

Q: Condition #1: Å structural support for a machine is subjected to a static compression load of 20 kN.…

Q: problem 1 pls complete solution

Q: 3.6. A short compression member with Do = 2Di is to support a dead load of 25 tons. The material is…

A: Given data Outer diameter, Do= 2Di F=25 tons Material is 4130 steel, WQT 1100 F Yield strength =…

Q: Given a 5.7meter Channel steel compression member (C7x12.25) with Fy = 345MPa. Calculate the design…

Q: A steel bar carries the axial loads at the positions shown. If E=200GPa, compute the maximum load P…

A: Given data: L1=1 mA1=500 mm2L2=0.8 mL3=0.4 mA2=A3=800 mm2E=200 GPaδ=5 mm Need to determine the…

Q: A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: (i) Stess at secion X-Xσ=P(b-ϕn)A=1000 X 103(100-25) X 12σX-X=111.1MPawhere b and T→ width and the…

Q: Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN.…

A: Write the formula for compressive stress generated in the rod due to the applied load. σc=PA Here, P…

Q: smooth pin at D and by vertical aluminum alloy [E = 10,000 ksi] bars attached at joints A and C. Bar…

Q: A part of a latch for a car door is to be made from a circular rod. With each actuation, it sees a…

A: Consider the diameter of the given rod is 3 mm. Write the given data. P1=780 NP2=360 N d=3 mm Here,…

Q: Question 5 Calculate the maximum longitudinal direct stress, plot the stress distribution diagram…

Q: 1. You are to design an axially loaded member that is to carry a load of 5,000 lb. The member is to…

A: Given:

Q: A link in a mechanism is to be subjected to a tensile force that varies from 3500 to 500 N in a…

A: Soln :- In a given problem we have a link that mechanism is subjected tesnile force which is able to…

Q: Problem 7: Analyse to determine the maximum service tensile live load force that can be supported by…

A: Calculation of diameter of hole dA=diameter bolt +side clearance =0.7+18=0.8336 in

Q: 13-12. Figure P13.12 shows a mec shear thin-gauge sheet metal. If a 200-N force is applied as shown,…

Q: Calculate the critical load of a strut which is made of a bar circular in section and 5 long and…

A: As per given question question Calculate the critical load of a strut which is made of a bar…

Q: A rigid pavement is designed to carry a static wheel load of 60.0 kN. If the allowable flexural…

A: The given data are: F=60 kN=60×103 Nσa=1.4 MPa=1.4×106 Pa Here, F denotes the load and σa denotes…

Q: Derive an expression for SF and BM for a Cantilever ca

A: given: Derive an expression for SF and BM for a Cantilever carrying UDL over the Entire span.

Q: 3.6. A short compression member with Do = 2Di is to support a dead load of 25 tons. The material is…

A: Given data: The dead load is F = 25 tons. The factor of safety is FOS = 2. The yield strength is Sy…

Q: Calculate the percentage error in finding the bulking load if the equivalent length for the freely…

A: Strut is a member or bar (in any position), which is subjected to axial compressive load. Column is…

Q: - Compare the critical stresses using E Rankine's formulae for struts with sle ratios, 50, 100, 150…

Q: A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric…

A: Given Su = 345 Mpa Force = 13 kN Given figure

Q: Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN.…

A: Condition #1 Given: The compression load, P = 20 kN The material used = SAE 1040 Hot rolled steel

Q: 10000 lb is applied at G, pin C can have 5000 max horizontal load and 6000 vertical load, determine…

Q: lb. The shaft diameter is 1.75 inches and has an ultimate stress of 60,000 psi, if the factor of…

Q: wwwwm Critically evaluate the deformation of the bar shown under the given loads.

A: first of all draw free body diagram of each bar and then perform calculations accordingly.

Q: A seamless cover plate for a full face gasketed, flanged joint has been designed. If a material with…

A: Given Data: Pitch circle diameter, d=477 mm Pressure, P=852 kPa

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

A structural support for a machine will be subjected to a static
tensile load of 16.0 kN. It is planned to fabricate the support from a
square rod made from SAE 1020 hot-rolled steel. Specify suitable
dimensions for the cross section of the rod.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook. Condition #2: The same structural support of the basic size determined in Condition 1 is subjected to a tensile load of 15 kN that is repeated several thousand times over the life of the machine. This load is not an addition to the 20 kN. Specify a suitable steel that is suitable to this application based on the basic size determined in Condition #1. Loading of Condition #1 does not apply here. Condition #3: The same structural support from Condition 2 is heated from room temperature of 25°C. The support is placed inside a frame on both ends. There is a total clearance of 0.2 mm between the support and its frame. Initial length of the rod is 200 mm. Specify the…
A structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook.
A structural support for a machine will be subjected to a static tensile load of 16.0 kN.Specify suitable dimensions for the cross section of the rod.
Condition #1: Å structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook.
Compute the design factor in the middle portion only of the rod AC if the steady vertical force on the boom is 2500 lb. The rod is rectangular, 1.50 in by 3.50 in, and is made from SAE 1144 cold-drawn steel. Include a mohr circle.
A link in a mechanism for an automated packag- ing machine is subjected to a direct tensile force of 1720 lb, repeated many times. The link is square, 0.40 in. on a side. Specify a suitable steel for the 3-3. link.
A 1000 mm cast iron pulley is fastened to a 112 mm shaft by means of a 28 mm squarekey 160 mm long. The key and shaft are SAE 1030 steel annealed with allowableshearing of key at 200 MPa and compressive of 660 MPa. a. What force in lbs acting at the pulley rim will shear the key?b. What force in lbs acting at the pulley rim will crush the key?
An aluminum rod, made from alloy 6061-T6, is made in the form of a hollow square tube, 2.25 in outside with a wall thickness of 0.125 in. Its length is 16.0 in. It carries an axial compressive force of 12 600 lb. Compute the resulting design factor. Assume that the tube does not buckle.
MACHINE DESIGN TOPIC A short compression member with Do = 2Di is tosupport a dead load of 25 tons. The material isto be 4130 steel, WQT 1100 F. Calculate theoutside and inside diameters in terms of incheson the basis of (a) yield strength, (b) ultimatestrength.*For 4130 steel, WQT 1100 FSu = 127 ksiSy = 114 ksi*Use the following Safety FactorsNu = 4Ny = 2
A leafs spring contains 4 full-length and 8 graduated leafs. The eyebolts at the support are 20 inches apart and the system should carry a load of 400 lbs. If the thickness of the available bronze plate is 1“ and Sy = 80 ksi, what leaf width is required at FOS = 8?
6. A circular bar is to carry a fluctuating torque from 25 to 55 N-m. Use AISI C1144 OQT 1000for the bar and compute for the required diameter for a design factor of 2. Attachmentsproduce a stress concentration of 2.5 near the ends of the bar. please also give the FBD, thank you
PCS Problem 105: Bearing Stress Explain briefly the purpose of the bearing plate between the steel column and the concrete pedestal.