Say we have an LED that will turn on when driven with a low signal from the output of a single logic gate. The two inputs to the logic gate are a 3 Hz digital pulse generator and a switch that goes low when the gas in a car gets below a certain level. We'd like the LED to flash on and off at 3 Hz when the gas gets low in the car. What type of single 2-input logic gate should be used in this situation? Draw the logic diagram.

Say we have an LED that will turn on when driven with a low signal from the output of a single logic gate. The two inputs to the logic gate are a 3 Hz digital pulse generator and a switch that goes low when the gas in a car gets below a certain level. We'd like the LED to flash on and off at 3 Hz when the gas gets low in the car. What type of single 2-input logic gate should be used in this situation? Draw the logic diagram.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 3:a) We can construct the full adder/Sub tractor with the help of AND-OR gate and also by using exclusive OR Gate. What is the between these two circuits?b) Construct the circuit of multiplexer which can multiply more than two bits.
The circuit shown in the figure is an example of A.) AND gate b) SPDT electronic switch C) inverter D) OR gate
In TTL, what are the two main kinds of output circuits?
Determine the LED "on" current for the circuit above. Assume the logic is 5V, VLED = 1.8V and VCE(sat) is negligible.
Draw plc ladder diagram in digital gates circuit
In motor control of train, IGBT control AC motor save more energy than GTO due to less switching loss. State THREE more reasons why IGBT use in motor control has many advantages over GTO. If one of the freewheeling diode in your single phase inverter in above settings has reverse recovery failure. Describe what would happen to the circuit.
Given the Flash analog to digital converter. a.) How many binary digits does it output? b.) What voltage does the over voltage pin go high? c.) What voltage does the undervoltage pin go high?
what is the MAXIMUM number of diode OR gates that can be cascaded before the output is not recognized as logic high?
Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF
Verify the following function using logic gates F=A.(B+C)
There are three logic gates. Logic gate A draws 3.6μA when the output is HIGH and 2μA when the output is LOW. Logic gate B draws 2.8μA when the output is HIGH and 1.5μA when the output is LOW. Logic gate C draws 1μA when the output is HIGH and 2μA when the output is LOW. Analyse which logic gate you would recommend for best power performance given operating voltage of 5V and 50% duty cycle. Associate your recommendation with appropriate steps and calculations.
Describe shift registers and it’s application.