Read the question carefully and give me right solution with clear calculations.  Note: pipe size required to carry the same flow rate at approximately one - third the pressure drop of the 3 in. pipe.

Q: Select a proper schedule of pipe for each of the following conditions: FOR SET B: Steam at at 900…

A: Given: Let us consider the given data, d=10 inP=900 psiaT=900°F To find: Proper schedule of pipe.

Q: 4. Consider fully developed laminar flow in the annular space formed by two concentric cylinders…

A:

Q: What is the energy loss over a sudden expansion from a DN65 Schedule 40 steel pipe to a DN125…

A:

Q: 10. What hose I.D. would be required to deliver 50 gal/min , assuming no friction losses at a…

A: GivenQ=50gal/min=0.189271 m3/minQ=3.1545×10-3  m3/sV=8.5ft/sec=2.5908 m/s

Q: Calculate the Reynolds number for the flow of each of the following fluids in a 2-in Schedule 40…

A:

Q: e height of the water

A:

Q: 1- What is the relation between the head loss and the velocity for the straight pipe? 2- Can we…

A: 1. The relation between the head loss and the velocity for the straight pipe is given by…

Q: Acetone at 77degrees flows around the tubes and inside the rectangular passage shown in the figure…

A:

Q: What is the velocity as measured by an orifice plate (0.06-m diameter) in a 0.305-m-diameter pipe…

A: Given that ,  d1=0.305md2= 0.06m∆P=75150Pa       =75.150kPa

Q: Calculatethe energy loss for water flowing at 8m/sthrough a standard tee fitting withan18-in ductile…

A: GIVEN:Water flow rate, Q=8m3/sDiameter of pipe=0.4572mFrom data book, MACHINE DESIGN DATABOOK BY VB…

Q: Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following…

A:

Q: 4- Is the flow rate effect the head loss and why? 5- What is the relation between the head loss and…

A: When fluid flows inside a pipeline or a duct , friction occurs between the layers of moving fluid…

Q: Q.1 Water is flowing through a 6” dia corrugated steel pipe. An energy loss of 2ft of head occurs…

A: diameter of pipe, d=6in=0.1524mhead loss, hL=2ft.=0.6096mlength of pipe, l=100ft.=30.48mfriction…

Q: Water at 60°F and one atmosphere is being transferred from tank 1 to tank 2 with a 2-hp pump that is…

A: As per the guidelines I can solve only first three subparts. Repost the other part.

Q: Pure milk at 293 K has a density of 1030 kg / m3 and a viscosity of 2.12 cp flowing at a rate of…

A: Write the given data with suitable variables: ρ=1030 kg/m3μ=2.12 cp=2.12×10-3 Pa-s10-3 Ps-s1…

Q: Pure milk at 293 K has a density of 1030 kg / m3 and a viscosity of 2.12 cp flowing at a rate of…

A:

Q: What is the expected head loss per mile of a closed circular pipe with 17 in. inside diameter…

A:

Q: Draw how it look if it is a laminar flow in pipe.

A:

Q: condition in a flow? a. If the flow is external and the velocity is measured close to the plate/wall…

A: Ans: (a) is correct.  there is a no-slip condition in a flow. If the flow is external and the…

Q: Ex. Closed pipe system the length is 130 m and 50 mm in diameter containing sixteen long elbows and…

A: Write the standard values of pipe fitting losses from pipe fitting losses equivalent length table…

Q: To compute the friction factors, you are assuming that the only losses in the system are due to…

A: Whenever fluid flow through the pipes there is always some kind of head loss is happened due to the…

Q: Fuel oil is flowing in a 4-in Sch maximum rate for which the flow is laminar. If the oil has a…

A: The head loss in the pipe can be calculated using the formula given below as- hf=32μuLρgd2 where, u…

Q: A 0.10-inch-diameter cappillary tube is filled with water at a certain temperature. The surface…

A: The value of capillary rise is calculated by using capillary rise formula, before putting values in…

Q: A 25% Calcium Chloride brine is to be pumped through a line at 250 gpm at a temp. of 0 deg. If the…

A: Given that, Flow rate of chloride, Q=250 gpm,Pressure drop inside pipe, ∆P=0.006 lb·force/in2-ft…

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: Part(a).From the given print,we can say that section A-A contains several parts.for example-It…

Q: When is no-slip condition possible? A. If the flow is external and the velocity is determined near…

A: The fluid property of viscosity is responsible for the no-slip condition and the formation of the…

Q: What level h must be maintained in Fig. to deliver afl ow rate of 0.015 ft3/s through the 1/2-in…

A: Given data: For Water at temperature 20 degrees Celcius                      Flow rate = 0.015 ft3/s…

Q: The rest of the questions are thus: 4) Calculate the air temperature and pressure in the pump at…

A: Given R=287 J/kg.k= 0.287KJkg.k Cp=1.005KJkg.k y=1.4 P1= 1 bar= 100 kPa T1=298 K   Explanation:…

Q: Using the appropriate equation from Table 4.3, calculate the wall sheer stress (in Pa) in a tube 5…

A:

Q: flow is lamin

A: given: value of reynold number for fluid flow in pipe and flow is laminar?

Q: Calculate the Reynolds number for 20oC water flow in a 1” nominal diameter sanitary pipe at Q=…

A:

Q: INDUSTRIAL PLANT ENGINEERING Select a proper schedule of pipe for each of the following conditions:…

A: Given Datad=10inP=900psiaT=900F

Q: Air at a pressure of 120 psig and a temp of 50 deg F is flowing at a rate of 500 lbs/ hr through a…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.