Please help me with this problem, Thank you Check if low Pressure and low velocity duct design system is applicable. Consider minor losses equivalentlength method with equivalent length of 10' for duct entrance loss, 35' for elbow loss, 8 for smooth reducerloss and 80' for reducer loss.GIVEN:V max = 1200 FPMFittings Equivalent Length (Le)Entrance, Le = 10Elbow, Le = 35'Diffuser, Le = 80'Pressure loss Max = 0.10 to 0.20 H,0/100 ft for low and Medium Pressure Loss DuctDuctIndex RunSection Duct Section JunctionFanA-1D-3E-SF-6F-GFan-AA-BD-EE-4ABCD(ADEFFDescriptionduct entrancemain ductreducermain ductelbowmain durtreducermain ductreducermain ductreducermain ductbranch ductelbowbranch ductelbowbranch ductelbowbranch ductreducerbranch ductelbowbranch ductelbowbranch ductreducerbranch ductelbowRectangular ducts are based on the table.Length L Q Velocity Pressure Loss Total AP Round Duct Rectangular+LeCFM fpm H00/1000 H20 W.G Dinch) Duct (WxH) inch2.137 1,2009.011 1800955410.0066 18.06955412,137 1,2001,939 11500.110.110.110.111,999 11501068635108200.110.110.110.1182817173519153517 24735247198822681,1971.197950 9809809909406057521481481966046047427421737135 371835348148106010603713713716057006006608409369367807907800.110.110.110.110.110.110.110.110.110.110.110.110.110.110.110.110.110.110.110.110.0088 17.58230390.0066 17.58030300.0885 14.38897770.011 14.38097770.0088 13.33167000.022 13.33167020.0088 12 11102190.002212.11102190.01876.697131686.697133680.0165 6.697131680.0385 6.697133680.0187 8043318280.0885 8.043318280.0187 7416450010.057.416456010.0009 11.48192280.0088 11.48192280.02:42 12.05990520.0385 12.05590520.0187 9.338464050.0385 9.338464050.0066 9318664050.0088 9.338464050.0088 9.338064050.05(3384640526x 1126x 11Z4x 112x 1120x920x917x917x916x816x86x66x66x69x69x68x68x614 x 814x914x911x711x711x711x711x711x7

V_max = 1200 FPM Equivalent length of minor losses Entrance, Le = 10' Elbow, Le = 35' Diffuser, Le =…

Check if low Pressure and low velocity duct design system is applicable. Consider minor losses equivalent length method with equivalent length of 10 for duct entrance loss, 35 for elbow loss, 8 for smooth reducer loss and 80 for reducer loss. GIVEN: Vmax=1200 FPM Fittings Equivalent Length (Le) Entrance, Le 10 Elbow, Le 35' Diffuser, Le-80 Pressure loss Max=0.10 to 0.20 H,0/100 ft for low and Medium Pressure Loss Duct

Check if low Pressure and low velocity duct design system is applicable. Consider minor losses equivalent length method with equivalent length of 10 for duct entrance loss, 35 for elbow loss, 8 for smooth reducer loss and 80 for reducer loss. GIVEN: Vmax=1200 FPM Fittings Equivalent Length (Le) Entrance, Le 10 Elbow, Le 35' Diffuser, Le-80 Pressure loss Max=0.10 to 0.20 H,0/100 ft for low and Medium Pressure Loss Duct

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If a machine has a mechanical advantage of 4 and ideal mechanical advantage of 6, then its efficiency is about 0.70% 70% 1.5% 150%
provide complete answer
I need the answer as soon as possible
Describe the principles of comparators and its qualities in field of engineering
Good morning interns, This is Ms. Gorman from the sales department. We have just secured a new, multi-million-dollar account! We are so good here in the sales department of Heavy-Duty Box Inc. The manufacturing director, Mr. Tsosie, has instructed me to send this problem out to all of you as this will be a deciding factor in which of you get offered the full-time positions available at the end of the internship! Our new client, Beastie Bearings Inc., needs the heaviest duty box we make here at Heavy-Duty Box for their bearings. The following email from Ms. Venegas from Beastie Bearings provides the information you will need. Remember, our mark-up sales price is 150% of what it costs us to manufacture the product. The cheaper it is for us to produce the box, the lower the cost for our client. There is also a grading rubric attached that Mr. Tsosie will be utilizing in evaluating your work. I would advise you to follow it well if you want a position! Good luck interns, Ms. Frances…
Paragraph Styles 3. Question 2 A car has a mass of 1.5 tons and a center of gravity at point G. The coefficient of friction between the rear driving wheel and surface of road is 0.25. Whereas the front wheels are free to rotate. 325 mm 205 mm 140 mm wu sti Figure 2: Various views of the car 2.1. Demonstrate all forces acting on a car. 2.2. Calculate the acceleration of the car. (11)
Questions Three Consider the office chair design below, develop the design matrix and identify its type. Answer
Provide and illustration to what is asked.
Solution 1: Ergonomic Assessment and Improvement. An ergonomic assessment of Paula's workstation could identify areas where adjustments could be made to reduce strain on her wrists. This could include adjusting the height of the workstation, providing wrist supports, or changing the design of the tools she uses. The strength of this solution is that it directly addresses the physical strain causing Paula's discomfort. However, the weakness is that it may require investment in new equipment or tools, and the effectiveness will depend on the specific changes made. Solution 2: Job Rotation. Paula could be rotated between different tasks more frequently, reducing the amount of time she spends on tasks that strain her wrists. This could also include training other workers to perform the welding and gaging operations, allowing for more flexibility in task assignments. The strength of this solution is that it reduces the repetitive strain on Paula's wrists. The weakness is that it requires…
A customer has recently tightened the specs for a part your company supplies. The specs are nowmuch tighter than the machine being used for the job is capable of. Briefly identify alternativesyou might consider to resolve this problem.
Please I want Mechanical and Physical properties of Human Femur Bone to Make a FEA in Ansys workbench. Thanks
solve please