R3010036Кеy way 5x2.56018R12535Ø40730Ø181501150Key way 5x2.5P306018081328.Ø1512Mate.Qty.1No.NameBodyNut M151CIMS1Slope 1:1003KeyWasherMS4MS135635Screw M12MS6.Stud M15MS3457Hand Wheel MS8.CenterAS12535$30R15M12R15P15M15Ø15080SIW

Answered: Image /qna-images/answer/0b9f9a1c-f02b-4449-bc46-a4613bd3b739.jpg

R30 100 36 Кеy way 5x2.5 60 18 R125 35 Ø40 7 30 Ø18 150 1 150 Key way 5x2.5 P30 60 180 8 5. 3. 132 8. Ø15 12 Mate. Qty. 1 No. Name Body Nut M15 1 CI MS 1 Slope 1:100 3 MS Key Washer 4 MS 1 35 63 Screw M12 MS 6. Stud M15 MS 3 4 5 7 Hand Wheel MS 8. Center AS 125 35 Ø30 R15 M12 R15 215 M15 Ø15 080 SIW

R30 100 36 Кеy way 5x2.5 60 18 R125 35 Ø40 7 30 Ø18 150 1 150 Key way 5x2.5 P30 60 180 8 5. 3. 132 8. Ø15 12 Mate. Qty. 1 No. Name Body Nut M15 1 CI MS 1 Slope 1:100 3 MS Key Washer 4 MS 1 35 63 Screw M12 MS 6. Stud M15 MS 3 4 5 7 Hand Wheel MS 8. Center AS 125 35 Ø30 R15 M12 R15 215 M15 Ø15 080 SIW

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve correctly
You want to put larger tires on your truck. The manufacturer tires are P265/65R18. You want to upgrade to P285/75R19. Complete the information below for each tire size. Please upload a picture//file of your work.
You must solve all questions.
Keino Thompson Problem 1. Given 2 parallel shalts with Required : h₁ = 3001pm d₁ N₁ = T₁ = + e = a) N₁ & N₂ b) p = center distance of 12.7 cm h₂ = 0.2 h₁ P = N₁ d₁ Power = = W d₂ Circular pitch of 10 teeth 2 Hp (Transmitted to pulley 2) gears in c) ng in rpm d) Pitch line velocities of Gears 1&2 of pulley 2 e) Torque in nm
In the cam-followers system shown, what is the magnitude of the slip velocity between the cam and the follower cm/s ? where o = 35.00, e= 20.00, w=7.00 rad/s, and R-20.00 cm. follower cam R V3 Vella rer a. None b. 102.55 90+36=129 c. 94.00 V2= 20x7 d. 85.45 %3D 140 CM/s e. 111.09 >
Use BS 4500A:1970 to determine the dimensional tolerance on the critical diameters in Gear Sub- assembly. The following tolerance should be determined (the limits and fits at each interface will be provided by Canvas): i. Bush & Shaft: Critical Diameter is 35 mm; (H8/f7) ii. Housing & Bush: Critical Diameter is 45 mm; (H7/s6) iii. Gear & Shaft: Critical Diameter is 20 mm (for the Right Gear) (H7/k6)
com/c/MTIXNZA5MTY31 TOWMDU3MTQXNZ15/details Tripie Beam Balance Practice Record the mass show on each balance. Remember to include both the value on the beams and the unit of measurement. 0 10 20 30 40 50 60 70 80 06 100g 100 200 300 400 500 g 10g 1. 0. 10 20 30 40 50 60 70 80 90 100g
Calculate the ankle torque during running pushoff from the following data set to 1 decimal place. NOTE if your answer is negative put the negative sign in the answer! Fz 1720 N Fx 551 N e to search CoP z 0 m Cop x 0.452 m Ankle z 0.143 m Ankle x 0.373 m Answer: Check B B M N Ps 2°C Partly sunny
Provided is A, B, C. I only need d to finish.
##L2Q8 A car has the following specifications m = 1599.8kg, l = 2669.6mm, w = 1539.3mm. Assuming a1 = a2, h = 760mm, m = 0.75, get the optimal tractive force Fx1/Fx2, which reaches the optimal maximum acceleration.
PQRS is a four bar chain PQ=56.3mm; QR=120mm; RS=102.3mm; PS = 100mm. The crank PQ rotates at 20 rad/s clockwise. The radial component of acceleration of Q will be with link PS fixed. The lengths of links are %3D m/s².
There are two pairs of closed soft tooth surface spur gears A and B Parameters of A: modulus m = 2mm, number of teeth Z, = 40,Z, = 90, width of teeth b =60mm. %3D Parameters of B: modulus m = 4mm, number of teeth Z, = 20,Z, = 45, width of teeth b = 60mm. %3D The accuracy of the two pairs of gears is grade 8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason?