RS=102.3mm; PS

Q: Dimension is 3/4” scale is 2”=1” what is the distance?

A:

Q: Q5: At the instant shown in figure (5) 04 = 6 rad/s, pulley A is given an angular acceleration a =…

A: Given data: The radius of the pulley A is rA=60 mm=0.06 m The initial angular velocity of the pulley…

Q: High precision in angularmeasurements can be made usinga sine bar. For using a 200 mm sinebar to…

A: Data available:Sine bar length is 200 mmL=200 mmDiameter of rolls is 35 mmd=35 mmInclined angle is…

Q: 90mm 60mm 45mm R15mm

A: Let’s divide the given section into 3 sections. Section 1 is a rectangular OABC. Section 2 is the…

Q: 4. The top of a male dovetail is 4 inches wide. If the angle is 55° and the depth is 5/8 inch, what…

A: 4.88''Explanation:Let's illustrate the problem,Given the width of the top of male dovetail which is…

Q: (a) The U-tube shown in Figure Q3 (a) is rotated about one of its arms at an angular speed of o…

A:

Q: 3

A: intro- defects on any material is cause of failure of material.

Q: n an engine, the piston diameter is 3 1/4 inches, the stroke is 4 7/8 inches, and the piston…

A: For the solution refer below images.

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: nd Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 G %3D…

A:

Q: Hot roof is one of the causes that contributed to the rise of temperature of indoor spaces in…

A: Hot roof is one of the major reasons on increased heat absorbtion and less albedo of the sun…

Q: If the main scale reading(mm) and vernier scale reading (division) are 29 and 18 respectively for a…

A: Solution:

Q: 1 2. 8. 09 Draw the isometric perspective of the part whose FRONT and TOP views are given below.…

A:

Q: 300 mm 30º 300 mm 300 mm Can someone please label the projection of F and the rest of the…

A:

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: The pipe assembly shown is subjected to a force F= 600 N. The pipe has an inner diameter of 20 mm…

A: Consider the Free Body Diagram: Torque,T=600*0.2 =120 N.mTorque acting on part BC,TBC=120 N.mTorque…

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: m. nd Find the components of the equivalent force. Express the re Express the z, y, and z components…

A: The position vectors are-

Q: pr... below. 5) Sketch the appropriate sectional view on the front view of the part

A: Given:To find:Sectional view on the front view.

Q: What is load-displacement?

A: It is related to a ship or a cargo vessel.

Q: shown in Fig. 2-13.2a. The inscribed grid with each square having a length of 1 ft locates each…

A:

Q: determine and plot the moment M rotate arm 0A over the range 0 < Find the maximum value of M and

A:

Q: (a) Figure Q2(a) shown the nut slides down the cord OA. When it is at the midpoint, its speed is 200…

A: Givenspeed=200mm/sAcceleration=10mm/s2

Q: Label all forces that act on the metal

A: A piece of metal is submerged in the liquid and one end of the metal piece is fixed with a string.…

Q: FRONT VIEW

A: According to the details provided in the question, we need to calculate ISOMETRIC VIEW

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: What company specification number is given to the material for this part?  2. What is the revision…

A: First of all , this engineering drawing shows the detailed assembly drawing of KM50 Head with the…

Q: y

A:

Q: Refer to the 1.914 dimension. B) What is its tolerance ? ________________________________ C) What…

A: Tolerance for the given dimension is 0.01. now as tolerance = upper limit - lower limit. and we also…

Q: Figure Q4 shows the values of the normal and shear stresses acting on a certain stress element which…

A: Given: Normal Stress in x direction→σx=-1.5 MPa Normal Stress in y direction→σy=1 MPa Shear stress…

Q: 10 mm Y 15 mm 30 mm 40 mm 10 mm 15 mm X

A:

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: The thin plate with four holes as shown in Figure 6 has a mass per unit area of 33 kg/m². The radius…

A:

Q: What does the slenderness ratio serve as?

A: The slenderness ratio is defined as the ratio of effective length to the least radius of gyration.…

Q: Determine the x, y, z components of reaction at the thrust bearing D 0 = 0°.

A:

Q: Compute the deflection of C after the load removed.

A: Given Conditions :

Q: You want to upgrade the tires on your truck. The manufacturer tires are P160/70R14. You want to…

A: 14 inch is the correct answer.

Q: 8. For the cross-section of a beam shown; a) locate the centroidal axis from the bottom of the…

A:

Q: Problem 2: Values: FA = 20 N FB = 30 N a = 25° Use the graphical method to determine... a) the…

A:

Q: 500N 100N 300mm 800 N 900 N 28°

A:

Q: c) The bore of each cylinder in a six-cylinder car engine is 52 mm and the stroke for each piston is…

A:

Q: 300 N 36 mm

A: We need to apply force equlibirium equation along the horizontal direction∑Fx=0Ax-C=0......consider…