Calculate the output for the given circuit.R2wwR2VoowwVeoR1Let the values are R1=303.5ohm, R2=835.21 ohm„The error voltage is =5.1 Volt.and the initial valueof output is 3 Volt.Vout =volt.%3D

Given: R1=303.5 ΩR2=835.21 ΩError Voltage=Ve=5.1 VInitial Value Of Output=V0=3 V

Answered: R2 R2 Vo oa ww R1

Engineering

Electrical Engineering

R2 R2 Vo oa ww R1

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

An analog signal varying between 1V and 3V will be converted to digital and the signal voltage value will be displayed on the LCD screen. The signal to be measured will be between 1V and 3V. 3 analog signals will be read using the AN5, AN6 and AN7 pins. Values in these signals will be displayed one by one on the LCD screen as digital and voltage values. Draw the circuit diagram and write the PIC C codes.
For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
Do calculation. This is not a simulation problem
FAIRCHILD Discrete POWER & Signal Technologies SEMICONDUCTOR ru 1N4001 - 1N4007 Features • Low torward voltage drop. 10 a14 * High aurge eurrent cepablity. 0.160 4.06) DO 41 COLOR BAND DGNOTEs CAT-Cos 1.0 Ampere General Purpose Rectifiers Absolute Maximum Ratings T-26*Cuness atnerwioe rated Symbol Parameter Value Units Average Recttied Current 1.0 375" lead length a TA - 75°C Tsargei Peak Forward Surge Current 8.3 ms single halr-sine-wave Superimposed on rated load JEDEC method) 30 A Pa Total Device Dissipetion 2.5 20 Derste above 25°C Ra Tag Thermal Resistence, Junction to Amblent 5D Storage Temperature Range 55 to +175 -55 to +150 Operating Junetion Temperature PC "These rarings are imithg valuee above whien the serviceatity or any semiconductor device may te impaired. Electrical Characteristics T-20'Cunieas ofherwise roted Parameter Device Units 4001 4002 4003 4004 4005 4006 4007 Peak Repetitive Reverse Vellage Maximum RME votage DC Reverse Voltage Maximum Reverse Current @ rated VR…
To lit the segment on for Common anode is O a. Connect A to +Vcc and give logic 0 to K O b. Connect A to 0 and give logic1 to K O. Connect A to +Vcc and give logic 1 to K O d. Connect A to 0 and give logic1 to K
What are IC Voltage regulators? State the different IC voltage regulators and its operation.
Two same size PV Modules are connected in Parallel. The specification of each module is given as, Number of cells = 36, Area of each cell is 12 cm x 12 cm. Assume the necessary data. Refer to the above PV Panel choose the correct statement. a. The output current of each PV Module is 2.15A b. The output current of each PV Module is 8.6A c. The output current of each PV Module is 4.3A d. The output current of each PV Module is 1.25A
Signal and system plz explain every step that how do this
Give the meaning of each acronym of solid state devices. Also sketch the schematic symbol for each device. SUS Shockley diode D-MOSFET JFET SCR DIAC THYRISTOR Device TRIAC 1. 3. 4. 6. 8. 10. 12. 14. Symbol 2. 5. 7. 9. 11. 13. 15. Meaning No entry
3. Graphical Representation of the signal 1) Write the type of the voltage from simulation results: 2) Write the value of the voltage from simulation result: L....... -2 DDU 12ns SónG Trace Color Trace Name X Values CURSOR 1,2 V(R1:1,0) Y1 Y2 Y1 - Y2 5.0373m 0.000 5.0373m 249.983 0.000 249.983 Y1(Cursor1) - Y2(Cursor2) Y1-Y1(Cursor1) Y2 - Y2(Cursor2) Max Y Min Y Avg Y 249.983 0.000 0.000 249.983 0.000 124.991
Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a e