R lock Page 7 of 8 Problem 6 14.0 kN 1.5 kN/m bam -1.0 m-1.0 m→* 2.0 m- For the beam shown above look at the location 1.1 meter to the right from the point A. Goal 1 (3 points) define formula to estimate shear force at the location of interest Goal 2 (2 points) calculate the value of shear force at the location of interest. Goal 3 (3 points) define formula for bending moment at the location of interest Goal 4 (2 points) calculate the value of bending moment for the location of interest.

R lock Page 7 of 8 Problem 6 14.0 kN 1.5 kN/m bam -1.0 m-1.0 m→* 2.0 m- For the beam shown above look at the location 1.1 meter to the right from the point A. Goal 1 (3 points) define formula to estimate shear force at the location of interest Goal 2 (2 points) calculate the value of shear force at the location of interest. Goal 3 (3 points) define formula for bending moment at the location of interest Goal 4 (2 points) calculate the value of bending moment for the location of interest.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The second moment of area of a rectangle is given by the formula I =bh^3/12where b is the breadth and h is the height.Determine the approximate percentage error, if b is measured 3% too largeand the height h is measured 1.7% too small.(Use the Binomial Expansion Method)
Construct the shear and moment diagrams for the loaded beam shown. After you have the diagrams, answer the questions. 1.2 kN/m W A Questions: Atx 1.1 m, V = W = w₁+kx² 1.9 kN/m 4.5 m x KN, M= i kN·m At x = 3.7 m, V = i KN, M= The absolute value of the maximum shear Vmax force is The absolute value of the maximum bending moment is Mmax i II kN·m KN x = r KN-m, x = r
Draw the shear and moment diagrams for the beam shown. After you have the diagrams, answer the questions. The distance x is measured from point A to the right. 265 Ib/ft 7.9' 3.7' Questions: At x = 3.9 m, V = ! Ib, M= Ib-ft At x = 9.8, V = i Ib, M = Ib-ft %3D The maximum absolute value of the shear force: |Vmax| = i Ib The maximum absolute value of the bending moment: |Mmax| Ib-ft %3D The bending moment is zero between the supports at x = i ft
Q2: Draw the load and the bending moment diagrams that correspond to the given shear force diagrams in the figures below.[ V (kN) Figure (1) V (kN) Figure (2) 114 11 94 14 x (m) x(m) 2. 1.4 18 -66 V(kN) Figure (3) V Figure (4) (kN) | 20 2 3 - 2nd-degree curve x(m) x (m) 1* degree 2nd degree -16 3 -13
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a= 2.5 m, b= 7.0 m, MB = 85 kN-m and Mc = 130 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. y MB Mc В C D Determine the shear force acting at each of the following locations: (a) x = 0+ m (i.e., just to the right of point A) (b) x = 2.5- m (i.e.,. just to the left of B) (c) x = 2.5+ m (i.e., just to the right of B) (d) x = 12.0- m (i.e. just to the left of D) When entering your answers, use the shear force sign convention. Answers: (a) V = i kN. (b) V - i kN. (c) V = i kN. (d) V = i kN.
Determine the shear force V in the beam at the point located 4.15 m to the left of point C. The ground reactions and shear-force diagram are shown. 65.60 kN 65.60 Units: KN 40.0 KN 3 m B 65.60 25,60 -23.7 kN -29.4 KN -19.0 KN -27.0 KN -21.0 kN 7.0 kN/m 12 m @x=6.66 m 58.40 kN -58.40
30 kN/m 50 kN-m A C D 3 m 1m 2 m Draw the shear and bending moment diagrams of the beam. Label all important points and distances. Annotate the degrees of curves. Show all supporting calculations. 1. Determine the location of zero shear relative to A. Determine the magnitude of internal bending moment at the location in item 1. 2. 3. Determine the magnitude of maximum shear and its location relative to A. 4. Determine the magnitude of the maximum bending moment and its location relative to A.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 2.2 m, b = 4.4 m, c = 3 m, P = 16 kN, w = 34 kN/m, and Q = 26 kN. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Additionally:(a) Determine V and M in the beam at a point located 0.65 m to the right of B.(b) Determine V and M in the beam at a point located 1.40 m to the left of C.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
5 kip/ft 15 kip ft 15 kip · ft B 6 ft 10 ft 6 ft Note: Attach your Shear and Bending Moment Equations and Diagrams and Solutions in the classwork tab. Make sure that your diagram is properly labeled and drawn.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a= 3.5 ft, b= 8.0 ft, t, c= 5.0 ft, d= 3.0 ft, w = 8.5 kips/ft and P = 54 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. P В D E b d Calculate the maximum bending moment (i.e., either positive or negative) that occurs between points B and C. When entering your answers, use the bending moment sign convention. Answers: M = i kip-ft.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a= 3.5 ft, b= 8.0 ft, t, c= 5.0 ft, d= 3.0 ft, w = 8.5 kips/ft and P = 54 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. P В D E d The shear-force diagram crosses the V = 0 axis between points B and C. Determine the location x (measured from A) where V = 0 kips. Answer: x = i ft.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a= 3.5 ft, b= 8.0 ft, t, c= 5.0 ft, d= 3.0 ft, w = 8.5 kips/ft and P = 54 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. P В D E d Use the graphical method to determine the bending moment acting at B (i.e., x = 3.5 ft). When entering your answers, use the bending moment sign convention. Answer: MB = i kip-ft.