Moving Plate F, V The gap between the two parallel plates contains two different fluids of viscosities ui = 0.1N.s/m? and uz = 0.15 N.s/m. The contact area of each plate is the same and equal to 1 m'. The thicknesses of the layers of fluids respectively are hi = 0.5 mm and hz = 0.3 mm. Determine: Fluid 2 P: Fluid 1 P i) Compute the fluid velocity at the interface between the two fluids. Find the force F to make the upper plate move at a speed of 1 m/s. i) Fied Plate

Moving Plate F, V The gap between the two parallel plates contains two different fluids of viscosities ui = 0.1N.s/m? and uz = 0.15 N.s/m. The contact area of each plate is the same and equal to 1 m'. The thicknesses of the layers of fluids respectively are hi = 0.5 mm and hz = 0.3 mm. Determine: Fluid 2 P: Fluid 1 P i) Compute the fluid velocity at the interface between the two fluids. Find the force F to make the upper plate move at a speed of 1 m/s. i) Fied Plate

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a.) Find the bulk modulus of elasticity of a liquid if a pressure of 150 psi applied to 10 ft3 of the liquid causes a volume reduction of 0.02 ft.3. b.) Find the capillary rise in the tube for a water-air-glass interface (θ = 0°) if the tube radius is 1 mm. Surface tension is 0.0728 N/m.
5Q. The plate is moving at 0.6 mm/s when the force applied to the plate is 4 mN. If the surface area of the plate in contact with the liquid is 0.5 m², determine the approximate viscosity of the liquid, assuming that the velocity distribution is linear. The thickness of the liquid layer is 4 mm. 0.6 mm/s 4 mm 4 mN
Plate with 0.13m wide and 0.25 m length passes thru oil ewith layer 3.5mm and 5mm thick. Both surface sides of the plate touch the oil that has a viscosity of u=0.038 Ns/m^2. Determine the force required (in Newton) to move the plate at speed of 5 mm/s
Water from a reservoir flowing through a deformable 600mm diameter pipe with a velocity of 2.5m/s is completely stopped by a closure of a valve situated 400m from the reservoir. Assume that the pressure increases at a uniform rate and that there is no damping of pressure wave. The pipe has a thickness of 20mm. Bulk modulus of water is 2.20x10°Pa and modulus of elasticity of steel is 0.14x10 Pa. Find the water hammer pressure for instantaneous valve closure.
Assuming that pressure will increase at a uniform rate and there is no damping of the pressure wave. Water from a reservoir that flows through a 650mm pipe at 1.8m/s is completely stopped by a closure of a 160 m valve from the reservoir. The thickness of the pipe is 25mm, bulk modulus of water is 2.2x10⁹ Pa and E of steel is 1.4x10¹¹ Pa. Determine the following: a. Celerity of the pressure wave b. Equivalent bulk modulus of water c. Pressure on the pipe after closure of the valve d. Time required to avoid water hammer e. Water hammer pressure of the velocity will decrease to 1.2m/s f. Maximum permissible discharge after the outlet valve closure. ANSWER: d) t = 0.256 sec. e) Ph=pCAV = 749.8476 kPa f) Q = AV = 0.597 m³/s a) C = 1249.746m/s b) k' = 1.562x10⁹ Pa c) Ph=pCV = 2249.5428 kPa
In horizontal pipe, which of the following is constant? Pressure headElevation headVelovity head 12
Plate with 0.13 m wide and 0.25 m length passes thru oil with layer 3.5 mm and 5 mm thick. Both surface sides of the plate touch the oil that has a viscosity of u=0.038 Ns/m^2. Determine the force required (in newton) to move the plate at speed of 5 mm/s
The velocity profile of water(density 1000 kg/m and viscosity of 0.001 N.S/m² ) in a pipe is u%=²(R² -r²) where R is radius of the pipe and r is any distance from the center of the pipe. %3D The roughness of the pipe is 0.03 mm. i. If the pipe is replaced by another pipe with higher roughness of 0.075 mm, Calculate the pressure drop in two-meter length of the pipe. ii. evaluate the pressure drop in two-meter. ii. Explain your answers (difference or similarity) in parts (i) and (ii).
Problem 1. In a test on an aerosol can it was loaded to a gage pressure p = 69.0 psi. While pressurized, the can is also subjected to a tensile axial load N = 400 lb and a torque T = 250 in - lb. The can has 3.0 in diameter and wall thickness t = 0.006 in. The cross-sectional area of the wall (thin ring) is A = 2rt and the polar moment of inertia of the wall (thin ring) with respect to the centroid is J= 2r°t. The maximum shear stress Tr on the surface is t=- J N T T. X The blue point on the surface of the aerosol can has its sides parallel and perpendicular to the can's longitudinal axis (x). Determine magnitudes of normal and shear stresses acting on the blue point. Ox = OL = oy = OH =. Sketch the stresses with their correct senses on the enlarged view of the blue point below.
Which of the following statements about HGL and EGL is correct? O For any pipe will a constant wall thickness, the slopes of EGL and HGL will be constant. O If the EGL falls below the pipe, then pressure head is negative, indicating a potential location of cavitation. O When a flow passage decreases in diameter, the distance between the EGL and HGL will increase. O When a pipe discharges into the atmosphere, both HGL and EGL will coincide with the system because pressure head is zero at these points.
2.Turbulent flow is defined as the fluid moves in layers.one layer gliding smoothly over adjacent layer true O False
A 40mm diameter rod 6m long elongates 12mm under load of 240kN. The diameter decreasesby 0.028mm during the loading. Determine the following:a. The Poisson’s ratio of the material,b. The Young’s modulus of the material, andc. The modulus of rigidity of the material.