please solve this questions in 40 mins i will give you positive feedback Question C3. Assume you are working in a design team and responsible to design a safebearing supports, and you need to first analyse the angular motion of a mechanical rigidbody system. Fig. 7 shows an equivalent mechanical system, in which, a homogenous diskof mass m = 4500 gm rotates at the constant rate w, of 145 rpm with respect to arm ABC,which is welded to a shaft DCE rotating at the constant rate w, of 9.5 rad/s. Assume themass of the bars ABC and DCE is negligible, and the important dimensions of the systemare shown in Fig.7. Determine(a) the angular momentum of the disc about the point C(b) the couple of the body representing the dynamic reactions at the support points Dand E,(c) Discuss the consequence of the unbalanced moment due to such motion andexplain the ways to address the issue.diskr = 195 mm210 mmDB210 mm325 mmE325 mmxFig. 7 (C3)

Answered: Image /qna-images/answer/040425ec-7401-41a0-9838-6eb8daf973ec.jpg

Question C3. Assume you are working in a design team and responsible to design a safe bearing supports, and you need to first analyse the angular motion of a mechanical rigid body system. Fig. 7 shows an equivalent mechanical system, in which, a homogenous disk of mass m = 4500 gm rotates at the constant rate w, of 145 rpm with respect to arm ABC, which is welded to a shaft DCE rotating at the constant rate w2 of 9.5 rad/s. Assume the mass of the bars ABC and DCE is negligible, and the important dimensions of the system are shown in Fig.7. Determine (a) the angular momentum of the disc about the point C (b) the couple of the body representing the dynamic reactions at the support points D and E, (c) Discuss the consequence of the unbalanced moment due to such motion and explain the ways to address the issue. disk r = 195 mm 210 mm B 210 mm 325 mm E 325 mm Fig. 7 (C3)

Question C3. Assume you are working in a design team and responsible to design a safe bearing supports, and you need to first analyse the angular motion of a mechanical rigid body system. Fig. 7 shows an equivalent mechanical system, in which, a homogenous disk of mass m = 4500 gm rotates at the constant rate w, of 145 rpm with respect to arm ABC, which is welded to a shaft DCE rotating at the constant rate w2 of 9.5 rad/s. Assume the mass of the bars ABC and DCE is negligible, and the important dimensions of the system are shown in Fig.7. Determine (a) the angular momentum of the disc about the point C (b) the couple of the body representing the dynamic reactions at the support points D and E, (c) Discuss the consequence of the unbalanced moment due to such motion and explain the ways to address the issue. disk r = 195 mm 210 mm B 210 mm 325 mm E 325 mm Fig. 7 (C3)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need these three parts answered, if you are unable to answer all three parts please leave it for another tutor to answer, thank you.
G tg Knowledge Check Answer the following. (a) Find an angle between 0 and 2x that is coterminal with 3 (b) Find an angle between 0° and 360° that is coterminal with-240°. Give exact values for your answers. JT (a) radians (b) IDon't Know Subnlit II
Q:04 Write a short note on the material used in the industry of Pakistan. Also write the products. Also write the products made in the industry from these materials?
Please make the charts for the questions. Please refer to Successful Project Management (7th Edition). Attached is the example Thank you.
Learning Goal: A centroid is an object's geometric center. For an object of uniform composition, its centroid is also its center of mass. Often the centroid of a complex composite body is found by, first, cutting the body into regular shaped segments, and then by calculating the weighted average of the segments' centroids.An object is made from a uniform piece of sheet metal. The object has dimensions of a = 1.45 ft, where a is the diameter of the semi-circle, b = 3.24 ft, and c = 2.10 ft. A hole with diameter d = 0.500 ft is centered at (1.13, 0.725). Figure X 1 of 2 Part A Find the area of the body. (Figure 1) Express your answer numerically in feet squared to three significant figures. ► View Available Hint(s) VE ΑΣΦ41 | vec A = 1.52 Submit * Incorrect; Try Again; 5 attempts remaining Part B I= Find I, the x-coordinate of the body's centroid. (Figure 1) Express your answer numerically in feet to three significant figures. ► View Available Hint(s) Submit Previous Answers Part C y =…
71.7 is being marked wrong in McGraw Hill homework. I thought I had done it right with putting 86.03 but that is wrong also. I'm not trying to just find the answer, trying to find how to do this. Could there be a different number than 71.7? Where does the μk=0.20 come into the equation?
What the ? I paid for you guys to help me with the homework? Nobody read the questions, just copy the answer from somewhere that not related to anything in my questions ? Please do the work please? Please don't give me this tutor again? Thank you for other tutor that will do the work.
You change your tries to bigger ones that have a diameter of 35.3 inches based on the circumference from above if your speedometer said you were driving 45 mph what is your actual speed
Mechanical Advantage Review Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your engineering design journal. Remember to show all work. 1. A lever has an effort arm that is 8 meters long and the resistance (load) arm that is 5 meters long, how much effort is needed to lift a 200 Newton weight?
Subject - Machine Shop & Theory
The class I'm taking is physics for scientists and engineers! **** I need help with part D only***** Can you please write out the solution and not type out the solution? I had to reask this question because the last tutor typed out the solution and it was very hard for me to follow . Please and thank you for the special request. I have attached the problem. Please view attachment before answering. Thank you!
LESSON: AUTODESK AUTOCAD Choose from the choices: