QUESTION 7 Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected to loads as shown in the figure below. Find the magnitude of internal reaction force, F., in section a-a in N. Enter only numeric value without units, but with correct sign. 200 mm 200 mm D 400 N 800 N

QUESTION 7 Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected to loads as shown in the figure below. Find the magnitude of internal reaction force, F., in section a-a in N. Enter only numeric value without units, but with correct sign. 200 mm 200 mm D 400 N 800 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the magnitude and sense of the forces in bars A and B in the figure shown below. Show all work.
Please zoom in
A force of F = 13 kips is applied as shown in the figure below. If the diameter of the bolt is d = 1.4 inches, find the maximum average shear stress in the bolt. Report your value in units of psi to one decimal place. F
1
L,=40mm; L,= 120mm; L=100mm and 0,=65°. Find the possible value of 0, and 0, L,=80mm and 3.
Shear Force Diagram and Bending Moment Diagram Determine the equations to draw the shear force diagram and bending moment diagram. Consequently, draw the shear force and bending moment diagram for the following load diagram. 2. 37 kN A 1.00 M 2.00 M
A steel bolt has a diameter of 8 mm. The bolt is encased by a bronze tube that has an outer diameter of 15 mm and inner diameter of 8 mm. A force is applied to the bolt. F d3 d1 F Values for the figure are given in the following table. Note the figure may not be to scale. Variable F₁ Value 25 kN Esteel 200 GPa Ebronze 105 GPa a. Determine the magnitude of the normal force in the steel bolt, Nsteel. b. Determine the magnitude of the normal force in the bronze tube, Nbronze. c. Determine the magnitude of the normal stress in the steel bolt, σ steel. d. Determine the magnitude of the normal stress in the bronze tube, Obronze. Round your final answers to 3 significant digits. N steel = KN Nbronze = KN σ steel = MPa Obronze = MPa
Consider the frame in (Figure 1). The crate weighs 400 lb. Follow the sign convention. Figure 4 ft A B 1.5 ft 1.5 ft 1.5 ft 1.5 ft F /C . E 0 D 0.4 ft < 1 of 1 ▼ Part D Determine the normal force at point E. Express your answer in pounds to three significant figures. NE = Submit Part E VE = Submit Determine the shear force at point E. Express your answer in pounds to three significant figures. Part F [5] 195| ΑΣΦ | 11 | vec 4 Request Answer ME = Π| ΑΣΦ I Request Answer vec Determine the moment at point E. Express your answer in pound-feet to three significant figures. [V=| ΑΣΦ www. vec ? ? ? lb lb lb-ft
The two rods (A-B and B-C) shown in the left panel are connected by pins at A, B, and C. The cross sections of A-B and B-C are 10mm×13mm and 10mm×10mm, respectively. The bilinear stress-strain relation shown in the right panel is for the material used to make the two rods, where Ei is the slope of the stress-strain curve for stresses between 0 and 80 MPa and E2 is the slope for stresses larger than 80 MPa. Note that Hooke's law is only valid for stresses up to 80 MPa. A 1 1 B 0.900 m 3 P = 30 kN 2.44 m C σ MPa 80 E₂ = 40 GPa E₁ = 80 GPa E a) Given the conditions above, find the axial elongation for each rod when subjected to P=30KN. b) Find the final position of Point B due to the applied load P at that location. Hint: Assume point B moves by unknown amounts Ax and Ay from its initial position, and then use right triangles to write the known final lengths of the cables in terms of Ax and Ay. The equations can be simplified by assuming terms Ax² and Ay² are so small they can be…
When they go to calculate both the normal stress of the bolt and the shear stress for the supporting material, they use both N and V =5 kip. I am very confused over this, shouldn't it be different forces? there is no x component being applied (Please clarify this ,Do not just solve)
Shown in the figure below is a parallel spring. If the allowable deformation is 25mm determine the value of P and the spring constant equivalent
You are designing a 1/4 inch diameter pin with a yield strength of 50,000 psi to hold 1000 Ibf. You are trying to decide between using the bolt in tension, bending, or double shear. Which setup is more likely to cause the pin to fail (by fail I mean yield or break)? Do not do any calculations for this problem, use your general understanding of the three different load cases. Double Shear Pin 券 Tension TT Pin Bending Pin O Tension O Bending O Double shear O All are the same