Question 4: The power/control system of an electric car consists of a 48-V onboard battery pack, electronic control/drive unit, and motor (shown in Figure below). If 180 A are drawn from the batteries, how many horsepower are delivered to the drive wheels? Power/ Drive To drive Batteries control motors wheels Efficiency: 95% Efficiency: 80%

Question 4: The power/control system of an electric car consists of a 48-V onboard battery pack, electronic control/drive unit, and motor (shown in Figure below). If 180 A are drawn from the batteries, how many horsepower are delivered to the drive wheels? Power/ Drive To drive Batteries control motors wheels Efficiency: 95% Efficiency: 80%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 8.5-hp, 200 V d.c. shunt motor running light tal sistance is 100 2 armature resistance is 0.6 2. Calculate: ) Speed regulation. ) The efficiency. i) The armature current at which efficiency is maximum
Report: 1. Draw in graph paper the relationship between the speed (5) and Torque(Ia). 2. Draw in graph paper the relationship between the speed (5) and Torque(Po). 3. Discuss the graphics between the (5 & Ia).
1. Consider the motor comparison problem on page 20 of Class Notes - 4. A slightly reworded version of the same problem is reproduced here for convenience and referred to as the "Base Problem": Base Problem 1: Two180-horsepower (HP) motors are being considered for installation at a municipal sewage-treatment plant. Motor 1 cost $5,800 and has an operating efficiency of 83%. Motor 2 costs $4,600 and has an efficiency of 80%. Both motors are projected to have zero salvage value after a life of 10 years. Let all the annual charges, such as insurance, maintenance, etc., amount to a total of 15% of the original cost of each motor and power costs be $0.05/kWh. Let the number of hours of full-load operation per year be denoted T. For what values of T is the purchase of Motor 1 justified if i= 6%? We found that purchasing Motor 1 is justified for T > 1,132 hours/year. ( a) Write out a solution to this problem neatly, showing the intermediate steps to arrive at T>1,132 hours/year. I suggest…
The field and armature resistances of a 243V series motor are 0.3 ohm and 0.1 ohm, respectively. The motor takes line current of 31 Awhile running at speed of 700 rpm. If the total iron and friction losses are 329 W, determine the motor efficiency in percent.
X A dc motor, 4kw, 160 volts, 1650 rpm, separately excited with armature resistance 1 ohm. The motor is used to drive through reducer of = 12 If the required load torque is 16 N.M and speeds 1.5 rad/sec. [1] Calculate the voltage reduction to drive the motor in such a required load? [2] The voltages appear on the motor *
A series motor runs at 800 rev/min when the voltage is 400V and the current is 25A. The armature resistance is 0.4 ohm and the series field resistance is 0.2 ohm. Determine the resistance to be connected in series to reduce the speed to 600 rev/min with the same current.
Q2. a) A four-pole, 415 V 50Hz induction motor supplies its rated power to a constant load. The rated speed of the motor is 1470 rpm. i) Draw the equivalent electrical circuit of the motor ii) Calculate the slip frequency and slip iii) If the supply voltage is changed to 207.5 V_25 Hz, calculate the motor speed, slip frequency, and slip. iv) Sketch torque-speed characteristics of the motor when the supply voltages are 415 V 50 Hz, 207.5 V 25 Hz and 415 V 60 Hz respectively; Compare the peak torques of the 415 V_50 Hz case and the 415 V 60 Hz case.
4- A 100kW, belt driven shunt generator running at 300rpm on 220V bus bars continue to run as a motor when the belt breaks, then taking 10KW. What will be its speed? Armature resistance is 0.0250; field resistance is 602; contact drop under each brush is 1V. 5- Calculate the reactance voltage for a machine which runs at 900rpm number of commutator segments is 65, brush width is 1.74 (in commutator segments), coefficient of self induction is 153µH. Assume linear commutation and neglect mica thickness and the conductor current is 27A.
We are given a motor which has a rated efficiency of 91.7% The current is 25/12.5 A and power factor is 82%, full-load speed is 1765 rpm, the voltage is 230/460 V (1) Check the efficiency is correct with the given data. (2) How much will it cost to run the motor at full load for 16 hours per day, five days a week, and 50 weeks a year. Assuming the plant has a contracted rate of 12 cents per kwh.
(b) During a course of Integrated Engineering Design, your group project's design requires a high torque motor to execute the desired task. The project would use a motor that has an equivalent circuit as in Figure 1. Based on the two motors listed in Table 1, choose the one that have higher torque to fulfil the requirement of your Integrated Engineering Project's design. Justify your answer by showing all the calculation details. Ia R. ww ME Vr Figure 1 Table 1 Parameters HS85013119 HS850136480 Rated terminal voltage / V 230 200 Rated current /A 35.7 38 Field resistance / m2 50 50 Armature resistance / m2 25 25 Rated speed / rpm 1200 1000 Stray losses / W 200 + x00 200 + x00 Where x is
1. Compare the reaction of Dc motor and dc generator. Also explain rule by which DC generator/motor works. No remarks added
A shunt generator delivers 195 Amp of terminal of voltage 250Volts. The armature resistance and shuntfield resistance are 0.02 ohm and 50 ohms respectively. The iron and friction losses equal to 950 Watts.The overall efficiency is?