X A dc motor, 4kw, 160 volts, 1650 rpm, separately excited with armature resistance 1 ohm. The motor is used to drive through reducer of = 12 If the required load torque is 16 N.M and speeds 1.5 rad/sec. [1] Calculate the voltage reduction to drive the motor in such a required load? [2] The voltages appear on the motor *

X A dc motor, 4kw, 160 volts, 1650 rpm, separately excited with armature resistance 1 ohm. The motor is used to drive through reducer of = 12 If the required load torque is 16 N.M and speeds 1.5 rad/sec. [1] Calculate the voltage reduction to drive the motor in such a required load? [2] The voltages appear on the motor *

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A DC shunt generator delivers 45 A at a terminal voltage of 220 V. The armature and the shunt field resistances are 0.01 2 and 44N respectively. The stray losses are 375 W. What is percentage efficiency of the DC generator
A DC generator with an armature resistance of 0.3 ohm and a shunt winding resistance of 125 ohm feeds a 250 Volt DC network. The idle losses of the generator are 750 Watts. What is the efficiency of the generator if it supplies 35A to the grid? la R C RE D
The DC shunt generator with the terminal voltage 350 V, armature drop 7 V and the each brush drop 2 V, then the value of generated emf is
A certain 110 V shunt generator has an armature and brush resistance of 0.06 ohm at full load of 85 A. The resistance of the shunt field is 45 ohms, and the stray power losses are found to be 897 watts. Determine the efficiency.
Q choose the correct answer: 1-Brushless excitation system consisting of.... a- Stator field winding and power diodes b-stator and rotor field winding and capacitor c- stator and rotor field winding and capacitor d- Everything mentioned in the options 2- Voltage generated per phase in an alternator is proportional to a- Flux per pole b- Number of turns in armature c-Winding factors d- Everything mentioned in the options e- Frequency of waveform 3- If input mech. Power of SG constant, the functionality of AVR is a- Control flux of rotor b-Control terminal voltage c- Control flux and terminal voltage d-Control Load angle
A 250 V d.c. shunt motor draws 4 ampere current from mains at no load and rotates at 700 r.p.m. Find out speed of motor when input power is 8 kW. Motor armature and field resistances are 0.6 ohm and 100 ohm respectively.
A 400V, 60HZ, 6-pole wye connected , 30 induction motor draws 75KW with a line current of 100A. The core loss is 2KW, Friction and Windage loss is 1.2KW. The stator resistance between two terminals is 0.352. What is the efficiency if the motor runs at a slip of 2.5%?
The factors effecting the speed of dc motor are The flux p and the voltage across the armature the voltage across the armature and the applied voltage V The applied voltage V, flux p and the voltage across the armature none of the aboye Indicate whether the following statement are true or false * True False The distance between the beginnings of each cascaded two coils is called commutator Pitch
The armature of a shunt generator has 0.08-ohm effective resistance. Each brush has an effective resistance of 0.02 ohm. The terminal voltage is 120 V while the current is 60 A. What is its efficiency?
A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit Part B Value I = HA Request Answer Submit If the dc-to-ac converter has a power efficiency of 90 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. HÅ Value Units Request Answer ? Units ?
16 A 2-pole d.c. shunt generator has a useful flux per pole of 0.03 Wb. The armature winding consist of 200 turns, each of 0.0052 resistance. Calculate the terminal voltage when running at 1200 r.p.m. if the armature current is *.40A none of the mentioned 210V O 230 V O 240 V O 200V O 220V O
4-pole, d.c. shunt motor has a flux per pole of 0.04 Wb and the armature is lap-wound with 720 conductors. The shunt field resistance is 240 Ω and the armature resistance is 0.2 Ω. Brush contact drop is 1V per brush. Determine the speed of the machine when running (a) as a motor taking 60 A and (b) as a generator supplying 120 A. The terminal voltage in each case is 480 V. 5 3 K4 8 Derive the Torque equation of a D.C Motor.