Question 3. Draw and design a Buck-Boost Converter circuit according to the Values given below. 22.06.2021 Input Voltage= 50 V Output Voltage=25V Switching Frequency=80kHz Output Power=150W Efficiency=85% Current ripple <1%*Input current Output Voltage Surge<1%*Output Voltage

Q: The output is out-of-phase with the input in   a. a common emitter circuit b. a common base circuit…

A: There are three types of BJT, namely, Common collector (CC) Common base (CB) Common emitter (CE)

Q: Assume Vcc= 18V, L₁= 5nH, C3 = 1000pF, total current drain of 1.5mA, Vo = 15Vp-p, Q = 100 R₁ · 10 ΚΩ…

A: According to the question, for the given circuit as shown belowVCC = 18 V, L1 = 5 nH, C3 = 1000 pF,…

Q: Please explain step by step (like the charging and discharging) how the output of this uncompensated…

A: The above circuit consists of a lead compensator made of resistors and capacitors. To this, a square…

Q: 4. The very small amount of reverse-bias current seen prior to reaching the breakdown voltage is…

A: When a diode is reverse biased, the is N-type material is connected to the positive terminal of…

Q: Flash analogue to digital converter is slower than counter type ADC. True False

A: The counter-type ADC is slow because the operation is performed in serial nature. All the different…

Q: In .................. mode of operation, fully controlled converter will keep a delay angle range…

A: average value of output voltage can be controlled by controlling the delay angle of thyristor.

Q: Define moore state machine. Draw Mealy state diagram of sequnce 1111 with overlapping condition.

A: The state diagram is visual representation of the sequence. It shows the internal states and…

Q: The most common technique to caneg analog to digital data is called Pulse Code Modulation(PCM). What…

A: The most common technique to caneg analog to digital data is called Pulse Code Modulation(PCM).…

Q: 4) Consider the clamping circuit below, assume Vref=3 V and Vin=5sin(wt) ..Draw the output voltage…

A:

Q: 20Vp Vout 9V 15V Group A Even SIDS Draw output wave for this circuit mentioning maximum and minimum…

A:

Q: A C-filtered center-tapped rectifier circuit is used to rectify sinusoid of 110 Vrms, 60HZ. The…

A: Given:V=110 Vrmsf=60HzMinimum output voltage=35Volttransformer ratio= 2:1load resistance, RL=1.8kΩ

Q: Calculate the output impedance for small-signal equivalent circuit. (R1=10 k2, r. =10 k2) ER, Rat O…

A: By drawing the small signal model of the given common emitter amplifier we can able to find the…

Q: C)Buck DC-DC Converter

A:

Q: A signal generator having a source resistance of 50 2 is set to generate a 1 kHz sinewave. Open…

A: Given, R= 50 Ωf=1000 HzV=10 V (peak-to-peak)VC= 8 V (peak-to-peak) It is asked to find the value of…

Q: loaded zener regulator, has the following parameters: Vin= 16V; the ener rated voltage 10V, series…

A:

Q: the given comparator and input signal V, draw the output waveform w.r.t the sinewave input signal…

A:

Q: Draw the circuit diagram of DC to DC converter using switched capacitor

A: We need to draw the circuit diagram of DC to DC Converter using switched capacitor.

Q: .a) Sketch the waveforms of inductor current, capacitor current and load current of a Buck…

A:

Q: Rout Ve

A:

Q: Discuss the importance of ADC (Analog to Digital Converters) in microchip designs.

A: We need to discuss the importance of ADC in microchip design.

Q: In a Common Emitter (CE) Fixed Bias (FB) configuration, the input impedance is almost equal to ---_?…

A:

Q: Consider a buck converter with input voltage of 100V and variable an output variable in the range…

A: CHOPPERS: A DC chopper is a permanently installed device that converts a fixed dc input voltage to a…

Q: 6 (b). The circuit below (Fig. 6.2) uses 2 D flip-flops to implement a divide-by-4 ripple counter…

A:

Q: Draw a schematic diagram of a full-wave bridge power supply.

A: Full wave bridge convert Alternating input to DC output which is used as the input source for…

Q: It has a simple structure II. Its efficiency is more than 90% III. It only requires one transistor.…

A: Given: η&gt;90% One transistor.

Q: a) For a half controlled rectifier with R-load (i) Draw the simple circuit diagram. (ii) Draw the…

A:

Q: If the given types of DC-DC Converter has an input voltage of 25V. The output voltage of each…

A: Given duty cycle D = 0.4  And input voltage Vs = 25 volts. For buck converter Vo = D*Vs. For boost…

Q: How does a Buck-Boost Converter work? Mention the application of Buck-Boost Converter

A:

Q: Instruction: Show complete solution. Use at least two decimal places. Express your answer in…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Design a buck converter and a resistive load operating in CCM mode with the following…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: a) Simple Diode and Zener Diode b) BJT and Diode c) Coupling Capacitor and Bypass Capacitor d)…

A: a. DIODE ZENER DIODE  1. UNIDIRECTIONAL 1. BIDIRECTIONAL 2.WORKS IN 2 WORKS IN FORWARD,…

Q: For the BJT circuit shown in Figure b, find the operation point of the transistor. (use B=100 for…

A: Solution: The modified circuit is,

Q: 1/1 The fixed bias provides good Q- Point stability. It is the most using .bias circuit False True

A: The fixed bias provides good Q-point stability.  It is the most using bias circuit.  True  False…

Q: Offset voltage compensating network is connected in between pin of LM741 op-amp number ....... &...…

A: LM741 is an 8-pin operational amplifier. A LM741 op-amp is shown below,

Q: A certain counting type 12 bit ADC operates with FSR = 0 to 10 V and clock Frequency folk 1 MHz.…

A: Given- 12 bit ADC, FSR=0 to 10 V, clock frequency fclk=1 MHz, To Find- (1) Dynamic range of…

Q: c) Explain the difference between the modulator and demodulator blocks and explain the terms…

A: Difference between modulator and demodulator: In the communication system, modulation and…

Q: Question-1: Consider the circuit in Figure below (Answer five only): 1. What the circuit type is? 2.…

A:

Q: 11. An SCR turn-off requires * anode current falls below holding current. reverse voltage is applied…

A: