QUESTION 20: The output stage in the following Figure is a Darlington pair emitter-follower configuration. Assume ß= 115 for all npn transistors and ß = 65 for all pnp transistors. Let V47 = 140 V for Q7, V411 = 148 V for Q11, and VA = ∞ for all other transistors. Calculate the small-signal resistance looking into the emitters of Q9 and Qg, i.e. Reg and Res, respectively. Hence, determine the output resistance Ro Reg (kn) Format : 9.92 Re8 (2) Format: 74.4 R₂ (2) Format: 22.67 V+ 26 V™ Bias - R, = 0.2 kΩ 27 29 = 0.2 mA ¹₂=0 eu 28 1c8= 1 mA I Ro OVO R₁ = 5 k

QUESTION 20: The output stage in the following Figure is a Darlington pair emitter-follower configuration. Assume ß= 115 for all npn transistors and ß = 65 for all pnp transistors. Let V47 = 140 V for Q7, V411 = 148 V for Q11, and VA = ∞ for all other transistors. Calculate the small-signal resistance looking into the emitters of Q9 and Qg, i.e. Reg and Res, respectively. Hence, determine the output resistance Ro Reg (kn) Format : 9.92 Re8 (2) Format: 74.4 R₂ (2) Format: 22.67 V+ 26 V™ Bias - R, = 0.2 kΩ 27 29 = 0.2 mA ¹₂=0 eu 28 1c8= 1 mA I Ro OVO R₁ = 5 k

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A transistor amplifier circuit is biased so that the quiescent point is to the far left of the load line midpoint. What do you expect to occur when the input voltage begins to vary? O The output voltage will be distorted on the bottom because it will hit the lower limit for VCE before the input voltage arrives at its peak. The output voltage will be distorted on the top because it will hit the upper limit for VCE before the input voltage arrives at its peak. O The output voTransistor's output voltage will look like the input voltage amplified and inverted. The output voltage will be zero (flat).
1. To use the Bipolar Junction Transistor (BJT) as a small signal amplifier it must be biased in this region: A. South Park region B. Spatial interface region C. Inverse Thevenin region D. Linear or active region
2. The parameters of the transistor as shown in the figure below are ß = 100 and VA = 100V. a. Find the dc voltages at the base and emitter terminals. b. Find Rc such that VCEQ = 3.5V. c. Assuming Cc and CE act as short circuits, determine the small-signal voltage gain Av = Vo/Vs. d. Repeat part (c) if a 5000 source resistor is in series with the vs signal source. V+ = +5 V Rs = 100 £2 www Us Cc RB = 10 ΚΩ I= Iausmi 0.35 mA www RC -000 V=-5 V CE
estion 2: Consider the BJT circuit given here. ( Write the input and output loop equations For the given values of Vcc= 10 V, Vin = 4V and resistor values, calculate all current values (IB, IC and IE) and VCE Assume that the ß for the transistor is 100 and the voltage drop across LED connected between Collector terminal and resistor (Rc) 2.1 V. TH i. ii. 111. VIN Vcc Rg=100 kΩ Re=2 kΩ LED 2.1 V B= 100 Based on the above analysis, correctly identify the current mode of operation Cutoff mode Active linear mode Saturation mode
Please don't copy
Common Gate MOSFET Amplifier has Select one: a. input is connected to the Gate and the output is taken from the Source b. input is connected to the Source and the output is taken from the Drain c. input is connected to the Gate and the output is taken from the Drain d. input is connected to the Source and the output is taken from the Gate 55 week 10 material Jump to... CE255/EE255 (01)- 16
Design a voltage divider biased CE stage with emitter degeneration. That stage should support a voltage gain of 5 and an input impedance larger than 3 KOhms with a bias current of 0.5 mA. Assume Beta=100, Is = 5e-17. Neglect the early voltage effect. You also need to provide values for the operating point of this transistor. Find the output resistance of this stage if the early voltage = 20 V.
Please Solve on paper ASAP
4. A Darlington transistor is essentially an array of two transistors connected as shown below. Assume both transistors follow our simple model with a current gain of B=100. Determine the maximum value of R2 that will just saturate the transistors, and pass full current through the load resistance R1. v2 V2 R2 PULSE (0 5 0) Q2 NPN R1 10 Q1 NPN V1 24
6.
To operate as an amplifier, it is the base of an npn transistor... Please select one: a. 0V b. positive by collector c. negative relative to emitter d. positive relative to emitter
For the circuit given below, transistor parameters are given as -= 0.1mA/V², Vth,p=-1V, A=0. Using these information, a) Design the circuit (find the values of R1and R2) such that Ip=100HA. b) Find the small signal voltage gain Vo/Vi of the circuit. R1 10 V - R2 ww0-2.5 V