Question 2 Sketch or draw the two-view drawing shown in Figure 2. Add the geometric dimensioning information per the following information: 1. Make the right-hand face in the right side view flat within 0.01. Identify this surface as datum feature A. 2. Make the top surface in the front view perpendicular within 0.01 relative to datum feature A. Identify this surface as datum feature B. 3. Make the right-hand surface in the front view perpendicular within 0.01 relative to datum feature B. Identify this surface as datum feature C. 4. Position the four holes within a 0.007 cylindrical tolerance zone at maximum material condition relative to primary datum feature A, secondary datum feature B, and tertiary datum feature C. 20.060 20.000 20 10.000 R20 Fig 2: 2-Drawing

Question 2 Sketch or draw the two-view drawing shown in Figure 2. Add the geometric dimensioning information per the following information: 1. Make the right-hand face in the right side view flat within 0.01. Identify this surface as datum feature A. 2. Make the top surface in the front view perpendicular within 0.01 relative to datum feature A. Identify this surface as datum feature B. 3. Make the right-hand surface in the front view perpendicular within 0.01 relative to datum feature B. Identify this surface as datum feature C. 4. Position the four holes within a 0.007 cylindrical tolerance zone at maximum material condition relative to primary datum feature A, secondary datum feature B, and tertiary datum feature C. 20.060 20.000 20 10.000 R20 Fig 2: 2-Drawing

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

do not reject . let other do the solution if u dont know. skip 86 30 ugh hole 16 6 20 Dig 28 18 Dia for the above isometric view , sketch the orthographic view in first angle proiection using catia v5 software. 36
3 igen action Senin All Kights Reserved. May sot be scanned, copied or duplicated, or posted to a publicly p 3. paubio Auadoud ajo MADE FRONT 'Z FRONT 3003 For the objects shown in isometric below, sketch the top, front, and right side views in the space provided. Make sure that your views are properly aligned. 1. 2. 78748 4. NO FRONT FRONT.
Sketch the missing side view and isometric view . Use CREO parametic 3.0 to sketch the figure Also show the hidden lines and dimension
Using the provided TOP VIEW and BACK VIEW please draw the ISOMETRIC PROJECTİON of the object below using ISOMETIRC PROJECTİON GUIDLINES . Make point X the lowest point of your drawing
The three planes of 'orthographic' projection of an object are presented in Figure 1.1 below. Draw by hand an isometric view of the object. The dimensions of your drawing are not important. Top View -2.00 4.00 -7.00- Front View 2.00 3.00 2.00 5.00 1.00- 4.00 5.00- -4.00- Side View
An isometric view of shaped part is shown. Draw in full scale the front view (indicated by the arrow F), top view and right-side view of the following object in First Angle and Third Angle Projection. All dimensions are shown in millimeters (mm). Dimensioning is required. You may show the construction lines but must be thin (0.3 mm). 35 38- 86 51 20 R10- 16 105- 16 F Figure: Question 1 32
I need help on questions 1-7 for this one please. They all coordinate together. Please refer to image as well. 1. Establish the right face in the side view as datum feature A. Qualify this feature with a flatness of .005. 2. Establish the top surface in the front view as datum feature B. Qualify this feature with a perpendicularity of .005 to datum feature A. 3. Establish the left surface in the front view as datum feature C. Qualify this feature with a perpendicularity of .005 to datum features A and B. 4. Establish all necessary dimensions as basic. 5. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 6. Position the three holes within a diamter of .012 at MMC relative to datum features A,B,C. 7. In the front view, identify the upper right corner as point "Y" and the lower left corner as point "X". Apply a profile tolerance of .020 between points X and Y relative to datum features A,B,C.
A Figure 2 shows an isometric view of an object. Draw to a full size scale the following views in first angle projection. (a) Sectional front view, (b) Top view and (c) Sectional side view C 80 B 28 10 54 50 S 25
Draw in full scale the front view (indicated by the arrow A), top view and right-side view ofthe following object in Third Angle Projection. Each isometric square shown on the drawingrepresents one square on the grid.
Problem: For the given front and Top views, (Drawn to scale) (All dimensions are in mm) A) Draw in the third angle orthographic projection: 1 Full sectional Top view(A A). 2- Left side view, B) Make an oblique drawing (45" to left) 15 Top 30 15 30 35 60 2x010 으20 A A Front 4XR10 40 R30 940X15DP
COMPLETE THE HORIZONTAL VIEW OF LINE AB, THEN PROJECT A TRUE LENGTH VIEW OFF THE HORIZONTAL VIEW. LABEL THE TRUE LENGTH OF THE LINE. SCALE: 1-10 ME BF AF NAME: AP COMPLETE THE FRONT VIEW OF LINE JK, THEN DETERMINE AND LABEL THE TRUE LENGTH OF LINE JK. SCALE: 1=5 (METRIC) Flp *P SCALE: NA 6.1
Draw in full scale the front view (indicated by the arrow A), top view and right-side view of the following object in Third Angle Projection. Each isometric square shown on the drawing represents one square on the grid.