Redraw the given orthographic views in full scale (1:1) and the corresponding section view. On another sheet, draw the oblique section view. 15 30 15 Ø160 - ø110 Ø16 45° Ø30 ? Use light pencil shade for the projection lines. Note: All dimensions are in mm. Ø30 Ø40 Ø70 15 FRONT VIEW RIGHT SIDE VIEW SECTION VIEW

Redraw the given orthographic views in full scale (1:1) and the corresponding section view. On another sheet, draw the oblique section view. 15 30 15 Ø160 - ø110 Ø16 45° Ø30 ? Use light pencil shade for the projection lines. Note: All dimensions are in mm. Ø30 Ø40 Ø70 15 FRONT VIEW RIGHT SIDE VIEW SECTION VIEW

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q) For the given two views shown in Fig. below draw the isometric projection use scale1:1 110 0- 15 60 R25 20 10 30- -60- -140 Left Side View Front View
2. the given two views shown in Fig. below draw the isometric projection use scale1:1 110- -08- 15 R25 20 10 e-30 -60- -140- Left Side View Front View
Produce the Front, top and Side VIEWS of the drawing shown below using appropriate scale and dimensions. ". 15 16 12 70 100 30 64 75 40 16
BLOCK 4 – Pictorial Drawing Use the orthographic drawings below for plates 1-3 100.00 Top View 50.00 20.00 70.00 Front View Right Side View Plate 1 Title: Cavalier Oblique Drawing Draw the cavalier oblique projection of the object. Use 45° for the third axis. cost 30.00 00'09
do not reject . let other do the solution if u dont know. skip 86 30 ugh hole 16 6 20 Dig 28 18 Dia for the above isometric view , sketch the orthographic view in first angle proiection using catia v5 software. 36
An isometric view of shaped part is shown. Draw in full scale the front view (indicated by the arrow F), top view and right-side view of the following object in First Angle and Third Angle Projection. All dimensions are shown in millimeters (mm). Dimensioning is required. You may show the construction lines but must be thin (0.3 mm). 35 38- 86 51 20 R10- 16 105- 16 F Figure: Question 1 32
Assignment 5 Figure 1 below shows an isometric pictorial view of a block Draw in 3rd Angle projection the following views; (a)Top, (b) Sectional Front View), (c) Side view show your Dimensions and use scale 1:1, neatness,and title block 62 50 16 23 50 FRONT ELEVATION Fig.1: Block
A Figure 2 shows an isometric view of an object. Draw to a full size scale the following views in first angle projection. (a) Sectional front view, (b) Top view and (c) Sectional side view C 80 B 28 10 54 50 S 25
Title: Object 2 Draw the isometric projection in this location. - 20 80 All dimensions are in mm 80 - 60 80 20 – 120-
I need help on questions 1-7 for this one please. They all coordinate together. Please refer to image as well. 1. Establish the right face in the side view as datum feature A. Qualify this feature with a flatness of .005. 2. Establish the top surface in the front view as datum feature B. Qualify this feature with a perpendicularity of .005 to datum feature A. 3. Establish the left surface in the front view as datum feature C. Qualify this feature with a perpendicularity of .005 to datum features A and B. 4. Establish all necessary dimensions as basic. 5. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 6. Position the three holes within a diamter of .012 at MMC relative to datum features A,B,C. 7. In the front view, identify the upper right corner as point "Y" and the lower left corner as point "X". Apply a profile tolerance of .020 between points X and Y relative to datum features A,B,C.
3 igen action Senin All Kights Reserved. May sot be scanned, copied or duplicated, or posted to a publicly p 3. paubio Auadoud ajo MADE FRONT 'Z FRONT 3003 For the objects shown in isometric below, sketch the top, front, and right side views in the space provided. Make sure that your views are properly aligned. 1. 2. 78748 4. NO FRONT FRONT.
COMPLETE THE HORIZONTAL VIEW OF LINE AB, THEN PROJECT A TRUE LENGTH VIEW OFF THE HORIZONTAL VIEW. LABEL THE TRUE LENGTH OF THE LINE. SCALE: 1-10 ME BF AF NAME: AP COMPLETE THE FRONT VIEW OF LINE JK, THEN DETERMINE AND LABEL THE TRUE LENGTH OF LINE JK. SCALE: 1=5 (METRIC) Flp *P SCALE: NA 6.1