Question 2/ How to: 1- Extrude faces in AutoCAD 3D modelling? 2- Draw a cylinder in AutoCAD 3D modelling? 3-Hide or Unhide the view cube display in AutoCAD 3D m
Q: Beiler Py000 P "punpin' Pumpl Turbine Condenser Figure 2 (b) Determine the themal efficiency of the…
A: given; at turbine inlet pressure P2=P3=6000KPa and temperature T=6000csuperheated…
Q: Q10/ A single block brake, as shown in figure, has the drum diameter 250 mm. The angle of contact is…
A:
Q: 2) Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at a…
A: Apply the thin cylinder concept, To proceed the problem.
Q: For the simply supported beam carrying the concentrated load P = 276 N at its midspan, determine the…
A: Given: P = 276 N at its midspan d = 2.16 m L = 2d = 4.32 m = 4320 mm E = 12.77 GPa =12.77 x 103…
Q: 4 kN m 1.5 kN m Bronze Aluminum Steel T. 100 mm 75 mm 2 m 1.5 m- :- -3 m- FIG. P3.11 FIG. P3.12 3.12…
A: Answer: (a) The maximum shear stress in each material: ◆ Bronze : 18.11 MPa ◆ Steel : 18.11 MPa ◆…
Q: A heat pump working on a reversed Carnot cycle has a COP of 4. It is made to work as refrigerator…
A:
Q: Wight Deflection 5 N High=10in 10 3.5 20 7 Width=1 in 40 16 20 9.9 10 Depth=5in 5 4 Calculation:…
A: Given dataHeight = L = 10 inch = 254 mm = 0.254 mThickness = t = 1 inch = 25.4 mm = 0.0254 mWidth =…
Q: Construct the third projection of the cylinder.
A: According to the details provided in the question, we need to calculate the third view.
Q: 9. Some of the motor is driven by inverter. Draw a Inverter control circuit for Mechanical brake…
A: Motors with various types of inverter drives are available with setup parameters to control the…
Q: The curve xy=3 is revolved one revolution about the x-axis between the limits x 2 and x=3. Determine…
A:
Q: Haw2 The compressive Stresf(r) of a rectangular beam sectionis given by the fokmuta: 6M P. bh where…
A: Givenσ=6Mbh2+PbhM=2.4×108 NmmP=6×105 Nb=300mmh=600mm∆M=3.6×106 Nmm∆P=18×103N∆b=-9mm∆h=-9mmfind ∆σ
Q: Homework one (Simple Stress) QI Two solid cylindrical rods AB and BC are welded together at B and…
A: Darw FBD
Q: Problem 7.1 The flywheel of an engine is 6 m in diameter. The maximum allowable stress in the…
A: We know that an engine's flywheel is 6 metres in diameter. The maximum stress that may be applied to…
Q: Q2/ A 3/4in-16 UNF SAE grade 5 bolt is subjected to a load of 8 kip in a tension joint. The initial…
A:
Q: To reach the maximum heat exchange rate, if a fan is applied, should it be upward airflow or…
A: Air on getting heated flows upward due to a decrease in its density with an increase in temperature.
Q: F6-8. Draw the shear and moment diagrams for th cantilever beam. 6 kN 12 kN-m B -1.5 m- -1.5 m- F6-8
A:
Q: The 20 kg solid disk moves up an incline under the influence of a force P = 200 N, acting on the…
A:
Q: F6-10. Draw the shear and moment diagrams for the simply supported beam. 6 kN/m 3 m- - 3 m- F6-10
A:
Q: 0.1: A composite strip made of unidirectionally glass fibers reinforced polyamide has a mass of 2.25…
A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…
Q: 0.1: A composite strip made of unidirectionally glass fibers reinforced polyamide has a mass of 2.25…
A: Given dataMass of the composite = 2.25 kgCross-section of composite = 3.5 cm x 2.5 cmLength of…
Q: Example: A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is m long. It is…
A:
Q: Determine the resultant of forces system shown in Figure and locate it with respect to point C?…
A: Find the resultant and distance from C.
Q: In a Series and parallel pumps, How to operate pumps in series and parallel? Explain briefly…
A: When a number of pumps are in parallel, the overall pump provides the net head equal to the head of…
Q: Determine the resultant of forces system shown in Figure with its direction and locate it with…
A:
Q: Haw2 The compressive Stresf (7) of a rectangular beam sectionis given by the fokmula: 6 M bh where…
A: Given equation for compressive stress of a rectangular beam section is σ = 6Mbh2 + PbhError in…
Q: produce ice at a final temperature of - 10 degrees * C from water at 27 degrees * C . The compressor…
A:
Q: The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure.…
A: Bar width, w= 2.25 in Bar thickness, t= 0.375 in Pin diameter, d= 0.775 in Applied load, P= 4800 lb…
Q: I50,000 CS 10,000s aasooo000O + 290 cs +41850000 t ISO,000 +aasoooo0oc the damping eta = 0.707 value…
A:
Q: How much thermal energy is created when a 2523 kg car brakes to a stop from 17.8 m's on a level…
A:
Q: Identify the correct moment and shear diagram for the following beam. 120 kN 1200 mm M V 144 kN-m-…
A: Draw the bending and shear force diagram.
Q: 14 How phase is measured in vibrakion Signels
A: Phase Measurement from Vibrations Signals . ****As per our company policy we are supposed to do only…
Q: + 290 Cs +41850000 t ISO,000c +aasooodc00 Ys 10,000s" Find the damping value of where zeta= 0707
A:
Q: 3. What kind of shape does the guide surface of the machine tool have? Among them, plane + plane In…
A: The main role of the guide surface of the machine tool is to ensure that the machine tool's…
Q: : Specific Heat of Liquids
A:
Q: What is induced drag on wings? Can the induced drag be minimized by (1) long and narrow wings or (2)…
A: Given question? What is induced drag on wing? Can it be minimized by wing shape?
Q: 5- Tensile Failure Vertical creates a vertical fracture parallel with the Oh Ov 6- Shear Failure…
A: Given Tensile stress question 5 Shear stress question 6 To find Option
Q: a) Determine the preload and service load stresses in the bolt. Compar to the SAE minimum proof…
A:
Q: 7. A well-insulated piston cylinder device contains 5L of saturated liquid water at a pressure of…
A:
Q: The 56.28 kg crate is hoisted up the 0 = 27° incline by the pulley system and motor M. If the crate…
A:
Q: 17. The molar volumes of a dry gas, measured at 200°F, are below. What is the coefficient of…
A:
Q: 7.(A). A steel bar ABCD consists of three sections: AB is of 20mm diameter and 200 mm long, BC is 25…
A:
Q: Q2/ A 3/4in-16 UNF SAE grade 5 bolt is subjected to a load of 8 kip in a tension joint. The initial…
A:
Q: The robotic arm shown below can reach horizontal distances away from its pedestal by rotating…
A: Given that, we have to consider the velocity and the acceleration of the point C in the horizontal…
Q: Completely solve and illustrate the problem. Show what are given, required, illustration, analysis…
A: given; diameter of solid shaft(ds)=4.2in =0.1068mweight of…
Q: nderstand 1) Determine the Internal forces of the following truss, having the foll 11 1 kip 2* 0.5…
A: To consider above given…
Q: 2z A fluid flow is given by: V = xy²i – 2yz²j – (zy² -k. Prove that it is a case of possible 3…
A: Continuity equation:- The continuity equation is a mathematical statement of the principle of…
Q: 27. Start with the one-group neutron diffusion equation and derive the relation for neutron flux in…
A: It has been viewed as that the climate is non-duplicating. In a non-duplicating climate, neutrons…
Q: A Eormula sheet (edf 114 KB An individual is performing a seated knee extension with a resistance of…
A: Given : L = 0.5 m W = 31 N F = 127 N To find : Torque
Q: Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1)…
A:
Q: Q1/A helical compression spring are required to exert a force of 45N when compressed to a length of…
A:
Step by step
Solved in 2 steps
- The title of our study is "Design and Fabrication of an Agricultural Spraying Attachment for an Autonomous Rover" we need help in the machine design part of our study, specifically Pump selection, battery selection, and center of gravity computation I already sent you the image of the rover Rover weight capacity 35 kilo grams (payload) Rover measurements: Wheel distance - 14.5 inches and 8.5 inches Rover platform size (width & length) 14.4 inches x 10.4 inches Height- 15.8 inches. Water tank selection More or less 25 liters *For tank selection we need to justify the size with the center of gravity, proving that is the maximum dimension or liters of the tank because the center of gravity will be higher making the rover prone to toppling Pump selection *Our sprayer design has two nozzles which splits using a tee splitter, we need to find the size of the pump to obtain the same discharge rate of a normal sprayer. A normal sprayer has a 12V pump and a pressure from 0.2 to 0.45 mpa…mechanical engineering : engineering drawing : AutoCAD Can someone please show step by step solution how to draw this in autocad 2D sketch ? With snapshotsThis problem comes from Introduction to Graphics Communications for Engineers 4th Edition page 64 #8 could you help me sketch the isometric view given the 3 standard views
- he figure shown below is a front and side view drawing of a mechanical product, which is amufactured by workshop machining: (dimensions are in mm) 1. Draw a sketch (free-hand drawing) of 3-D isometric of this product? 2. Suggest (t) a suitable design software program for this product, and justify your selection? (explain why you select it based on other alternatives) 3. Can you suggest what is the name of this product and where it can be used? Select a suitable material for this product and why? 4. Develop a suitable GT code based on Opitz code and explain it? 5. Read the tolerance on the figure? And explain what is 3-2-1 datum system based on the figure below? 6. Explain – in details - the required process planning for machining this product 7. What engineering analysis is required for this product? Explain in details? 8. write a CNC program for machining this product? 9. Select -with details- the suitable inspection program for testing the geometry of this product? 4X 3.1-3.2 +0.2 AB…Can you make it for me?(image below)just screenshot the result after you make the shape on the autocad and give it to me,thanksWhat is/are the important commands/steps to begin 3D drawing?
- question from ENGINEERING DRAWING BY N.D BHATT Draw rough sketch of front , Top and side view of following 3D model using first angleprojection?What is the difference between the terms "perspective projection" and "orthographic projection"? "perspective projection" = all the lines from the original point to the projected point intersect at a single point "orthographic projection" = all the lines from the original point to the projected point are parallel "perspective projection" = all the lines from the original point to the projected point are parallel orthographic projection" = all the lines from the original point to the projected point intersect at a single point "perspective projection" = all the lines from the original point to the projected point are parallel "orthographic projection" = all the lines from the original point to the projected point intersect at one of the two focus points of an ellipse "perspective projection" = all the lines from the original point to the projected point intersect at one o the two focus points of an ellipse "orthographic projection" = all the lines from the original point to the…create a shape design 2d on autodesk inventor professional 2020, screenshot pllsss
- Please sketch the figure in catia v5 , no hand drawing ,please I need ,don't reject ,skip if don't have the softwareYou have been selected by an engineer for them to design their newest robotic prototype. As of this moment it is your job to come up with a purpose of the robot and incorporate various types of conic sections into its designGiven the art below, what type of perspective is used to create the illusion of three-dimensions, and how do you know this? Use complete sentences. O 2019 Glynlyon, Inc. UPLOAD