The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure. The bar width is w = 2.25 in. and the bar thickness is 0.375 in. For an applied load of P = 4,800 lb, determine the average bearing stress produced in the bar by the 0.775-in.-diameter pin. Express your answer in psi rounded to the nearest hundredths. Answer: Blank 1 Bracket Pin Bar

The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure. The bar width is w = 2.25 in. and the bar thickness is 0.375 in. For an applied load of P = 4,800 lb, determine the average bearing stress produced in the bar by the 0.775-in.-diameter pin. Express your answer in psi rounded to the nearest hundredths. Answer: Blank 1 Bracket Pin Bar

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.3P: A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the...

See similar textbooks

Similar questions

Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
, Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14 kN/m, and L = L2 m.
A solid aluminum shaft of 100 mm diameter fits concentrically in a hollow steel tube. Determine the minimum internal diameter in mm of the steel tube so that no contact pressure exist when the aluminum shaft carries an axial compressive load of 503 KN. Assume Poisson's ratio = 1/3 and a modulus of elasticity of the aluminum rod is 75 GPa. Use 4 decimal places. Add your answer
Solve for the indentation diameter if the BHN of the material is 70 and a 500 kg of load is applied? Use indenter diameter 10mm.
3. The aluminum block has the rectangular cross-section and is subjected to an axial compressive force of 8 kips. The 1.5-in side changed its length to 1.50014 inches. Use E = 10 x 10³ ksi. Calculate the new length of the 2-inch side. Answer: Lnew = 2.00019 in 1.5 in 2 in. 8 kip- 8 kip 3 in. 4. A solid cylinder of diameter D is subjected to an axial load P. Show that its change in diameter is 8D = 4Pv/лDE.
The rectangular bar shown is connected to a support bracket with a 27 mm diameter pin. The width of the rectangular bar is 90 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket.just bearing stress in the rectangular bar. Rectangular bar Support - bracket
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.
The rigid bar ABC supports a load of 21.1 kN at point C. A circular rod (diameter 25 mm) supports the bar at B. The length of AB is 3.5 m and the length of BC is 1.1 m. Calculate the normal stress in the rod. Provide your answer to 2 decimal places in MPа. Rod diameter = 25mm В y F kN
Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of the link and its length are given in the table below for cach student. The alloawble stress of link BD is 200 MPa. a) Determine the maximum possible value of the load P b) If P-90 kN, determine the change in temperature needed for link BD to have no change in length. Given Me=12*10/"C, E,200 GPa B A 0.4m 0.2m
Answer the ff correctly. The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.