2 Question # 2: Find the transfer function, G(s) = 01(s)/Ea(s) for the motor and load shown in the figure. Thetorque-speed curve is given by Tm = -8 cm + 200 when the input voltage is 100 volts.e(t) MotorJa = 1 kg-m²Da = 5 N-m-s/radN₂ = 100N₁=20N₁100N3 = 25OL(1)HEJL = 400 kg-m²DL 800 N-m-s/rad=

Given system represents the mechanical rotational system. The general equation for a mechanical…

Question # 2: Find the transfer function, G(s) = 01(s)/Ea(s) for the motor and load shown in the figure. The torque-speed curve is given by Im = -8 m +200 when the input voltage is 100 volts. (1) Motor Ja = 1 kg-m² Da = 5 N-m-s/rad N₂= 100 N₁=20 | |N₂= 25 N₁ = 100 OL(1) Ho JL = 400 kg-m² D₁ = 800 N-m-s/rad

Question # 2: Find the transfer function, G(s) = 01(s)/Ea(s) for the motor and load shown in the figure. The torque-speed curve is given by Im = -8 m +200 when the input voltage is 100 volts. (1) Motor Ja = 1 kg-m² Da = 5 N-m-s/rad N₂= 100 N₁=20 | |N₂= 25 N₁ = 100 OL(1) Ho JL = 400 kg-m² D₁ = 800 N-m-s/rad

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

To modeling separated excited DC motor by transfer function, you need to the math operation library to reach to the following blocks Gain Add Constant Product
Determine the values, of K and k of the closed-loop system shown in Figure below so that the maximum overshoot in unit-step response is 25% and the peak time is 2 sec. Assume that J = 1 kg-m² .
Please answer this,I want a detailed explanation. An a.c. supply drives a half-controlled thyristor bridge with a resistive load. Sketch the circuit diagram, and the voltage and current waveforms.
i just want a paragraph of these sensors and their function and which is best then the other.PZT-5HPZT-5JModif. PZT-5A
9| Design Dc Dc converterto produced -15 V out put Prom Source Varies from 12 to 18 V. The load Resistance 15r.
What is amplitude modulation
A step down converter is feeding an inductive load with R-10 Ohms, L15 mH and E-1sV. The supply is Vs-200v, the switching frequency is 10 kHz and the duty cycle is k-0.5. The maximum peak to peak ripple current in the load is equal to 0.34A. The erage load current la would be equal to: Select one: a. 8.5A O b. 18A Oc 11A O d. None of these
What is unit step signal
Problem: If the no-load output voltage of a regulator is 15.5 V and the full-load output is 14.9 V, what is the percent load regulation?
In order to control a DC motor from a computer : O We need a DAC such that data will flow from computer to DAC and from DAC to DC motor O We need an ADC such that data will flow from computer to ADC and from ADC to DC motor We need an ADC such that data will flow from computer to ADC and a DAC so data flows from DC motor to computer
signal subject notice for 2 b(i) use integration way and prove the answer with graph
What is transition ?