Question 2 Calculate the amount of DC current required for the magnetic circuit given below to generate a flux density of 1.0T in the airgap. The details are Number of turns, N-400 The core is made up of steel, the B-H characteristic has been given below The magnetic core length, le = 500 mm The airgap length, lg 2 mm The cross-sectional area of the core, Ag 100 mm? Neglect leakage and fringing.

Question 2 Calculate the amount of DC current required for the magnetic circuit given below to generate a flux density of 1.0T in the airgap. The details are Number of turns, N-400 The core is made up of steel, the B-H characteristic has been given below The magnetic core length, le = 500 mm The airgap length, lg 2 mm The cross-sectional area of the core, Ag 100 mm? Neglect leakage and fringing.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A ferromagnetic core is shown below. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.003 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. 1. - 10 cm--- - 20 cm - 15 cm 500 tums 15 cm 15 cm [1.21 A, 0.4 T, 1.2 T]
B. For the following magnetic circuit, the flux passing through the core is 1.32 mWb, the cross section of the core is 3 cm by 4 cm, the laminated section has a stacking factor of 0.9, and the gap is 1 mm. Determine the flux density in each section. Neglect fringing d N turns Cast iron Air gap Laminated sheet steel
QUESTION 1 A ferromagnetic core is shown in Figure 1. The depth of the core (in to page) is 15cm, and the other dimensions are shown in the figure. There is a 150-turn coil wrapped around the left side of the core with input current is 2 Ā. a) Draw and label a magnetic circuit of ferromagnetic core below b) Assuming relative permeability, pr of 2400,calculate: i. Total reluctance ii. Magnetomotive force of the circuit Total flux of the circuit ii. 15cm 20cm 15cm 15сm N= 150 20cm 15cm 15cm 20cm 15cm Figure 1: Ferromagnetic Core
A toroidal core with a mean circumference of 100 cm and a cross-sectional area of 10 cm2 is wound with 500 turns of wire. What current would be required to generate a flux of 1 mWb in the core. Assume the core has a relative permeability of 800
(a) Explain briefly what is fringing effect and leakage flux. (b) A ferromagnetic core is shown in Figure 1. The depth of the core is 10 cm. The other dimensions of the core are as shown in the figure. By assuming the magnetic leakage to be negligible and relative permeability of the core is 800. Calculate the total reluctance and find the value of the current that will produce a flux of 0.01 Wb. With this current, calculate the flux density at the top of the core 20 cm 40 cm 10 cm, 30 cm 500 turns 30 cm 30 cm Figure 1
Example(6): A magnetic circuit containing an air gap is shown in Figure below. With the dimension as marked, calculate the current in the coil to establish a flux density of 0.6 T in the air gap. The core has the B - H characteristics. Repeat above but correct for fringing and lamination. Consider SF=0.95, FF 1.08 while is as above. 2 mm) A-5cm²
The figure shows a ferromagnetic core. The core depth is 5 cm. The other dimensions of the core can be seen in the figure. Find the value of the current produced by a flow of 0.005 Wb. With this current, specify the flux density on the right side of the core. Assume a relative core permeability of 800 and a 0.0017 cm gap between the thinnest part of the core. 15 cm N= 500 0.0017 cm 15 cm 15 cm - 10 cm af- 20 cm Depth 5 cm
A magnetic circuit with a cross-sectional area of 20 cm? is to be operated at 50 Hz from a 120 V rms supply. The number of turns required to achieve a peak magnetic flux density of 1.8 T in the core is
Question 1 A ferromagnetic core with a relative permeability of 1500 is shown in Figure 2. The dimensions are as shown in the diagram, and the depth of the core is 7 cm. The air gaps on the left and right sides of the core are 0.070 and 0.020 cm, respectively. Because of fringing effects, the effective area of the air gaps is 5 percent larger than their physical size. If there are 400 turns in the coil wrapped around the center leg of the core and if the current in the coil is 1.0 A, what is a) the flux in each of the left, center, and right legs of the core? b) the flux density in each air gap? 7 cm ст ст 30 cm 30 cm 7 cm 400 turns 0.05 cm 30 cm 0.07 cm 7 cm Core depth = 7 cm Figure 2
5. A toroidal core with a mean circumference of 100 cm and a cross-sectional area of 10 cm2 is wound with 500 turns of wire. What current would be required to generate a flux of 1 mWb in the core. Assume the core has a relative permeability of 800 а. 1.0 А c. 1.5 A b. 2.0 A d. 2.5 A
The applied MMF to a simple magnetic circuit is 350AT. It was found that the resulting magnetic field denstiy is 0.7 Wb/m². The average length of this magnetic circuit is 1.64ft and its cross sectional area is 4cm². What is the reluctance (in AT/Wb) of the magnetic material of the core?
Q1. Figure 1 shows the magnetic circuit with cross section area of core, 1000 mm2 and current source, 10 mA. By assuming the absolute permeability of core is 2.513x103 H/m, analyze the circuit and determine the following parameters: a. Draw the equivalent Ampere Circuital Law model b. Total reluctance of magnetic circuit c. Magnetic flux at centre and both sided d. Magnetic flux density at centre and air gaps e. Magnetic flux strength at centre and air gaps f. Briefly explain, effect to the magnetic circuit if the length of air gaps keep decreasing and increasing. at 7 cm 30 cm 30 cm 7 cm 7 cm 30 cm 1 cm 400 turns 1 cm 7 cm Figure 1 B-H CURVE BIT) 16 Sheet steel Cast steel 14 12 1.0 08 Cast iron 0.6 04 0.2 H(AUm) 500 1000 1500 2000 2500 3000 3500 4000 4500 5000