Question 2 A valve is used to regulate flow in a water pipeline. The pipe has a diameter of 400 mm and runs for a length of 2500 m. 1. Discuss the effects of a water hammer on a pipeline. 2 2. Calculate the critical period of the pipe 3. Determine the surge pressure if the valve is closed in (a) 3 s (b) 5 s Assume the bulk modulus for water is 2.08 GPa and all pipes are made of steel with wall thickness of 10 mm and modulus of elasticity of 120 GPa. Take the factor k 0.9.

Question 2 A valve is used to regulate flow in a water pipeline. The pipe has a diameter of 400 mm and runs for a length of 2500 m. 1. Discuss the effects of a water hammer on a pipeline. 2 2. Calculate the critical period of the pipe 3. Determine the surge pressure if the valve is closed in (a) 3 s (b) 5 s Assume the bulk modulus for water is 2.08 GPa and all pipes are made of steel with wall thickness of 10 mm and modulus of elasticity of 120 GPa. Take the factor k 0.9.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the pressure drop over a reducer with the following conditions: Fluid density: 25 kg/m3Fluid velocity: 1.5 m/sFluid viscosity: 0.001 Pa*sInlet diameter: 0.12 mOutlet diameter: 0.019 mPipe absolute roughness: 4e-4 m Give your final answer in Pa, rounded to the nearest whole number. [Ignore entrance/exit losses and velocity loss terms]
1. An 80 mm schedule 40 steel pipe is 1800 m long and carries a lubricating oil between 2 points A and B such that the Reynolds number is 1200. Point B is 10 m higher than point A. The oil has a specific gravity of 0.85 and dynamic viscosity of 6.51 X 10-1 Pa.s. If the pressure at A is 345 KPa, calculate the pressure @ B. 2. Determine the energy loss for a sudden contraction from a 4 in schedule 80 steel pipe to a 1.5 in schedule 80 pipe for a flow rate of 250 gal/min. 3. Determine the equivalent length in meters of pipe of a quarter open gate valve placed in a DN 250 schedule 40 pipe.
SAMPLE PROBLEMS #3 A venturi meter with a 10.16 cm throat is installed in a 15.24 cm pipe which is inclined upward at an angle of 45 degrees to the horizontal. If the distance between pressure tape along the pipe is 1.5 m, the differential pressure is 70 kPa, and the water temperature is 70°C, what is the discharge of water in m'/sec? Assume coefficient of 0.985.
A 400 gpm piping system is composed of the following pipes and fittings. Using the chart; Determine the Following: a. Equivalent length at suction in ft b. Equivalent length at discharge in ft c. Total friction loss in the installation, in ft. Suction side (4.5” Փ) Length of straight pipe 210 ft Long sweep elbow 5 pcs Standard Tee 2 pcs Globe valve 1 pc Checked valve 1 pc Gate valve (fully open) 1 pc Discharge side (4.0” Փ) Straight pipe 200 ft Standard elbow 4 pcs Standard Tee 3 pcs Gate valve (fully open) 1 pc
B1. A water with viscosity 11.4x10-3 poise is flowing through a pipe of diameter 300 mm at the rate of 500 litres per sec. Find the Reynold's Number & the head lost due to friction in the pipe of length 1 km. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) The velocity of flow of water (in m/s) is The value of Reynold's Number is The frictional loss in the pipe (in m) is
1. What is the likelihood that a flow with an average velocity of 0.15 f t/s in a 6 in. water pipe is laminar? Find the speed at which the flow will always be laminar. 2. If the critical Reynolds number for a river is 2000 based on average velocity and depth, what is the maximum speed for laminar flow in a river 10 f t deep? 2 f t deep? Do you expect any river flow to be laminar?.
2. A turbine is used to produce 2700 hp by expanding the water between points 1 and 2. Water flow rate, static pressures and pipe diameters are given. Calculate the power lost in between point one and two. Note that the static pressure at point 2 is given in vacuum. (SGH =13.6) P1 = 60 psi Q = 150 ft³/s D = 3 ft Section (1) Turbine 10 ft P2 10-in. Hg %3D vacuum D2 = 4 ft Section (2)
Select the proper-sized steel tube for a flowrate of 25 gpm and an operating pressure of 1,000 psi. The maximum recommended velocity is 20 ft/s and the factor of safety 8. The tube is made out of SAE 1010 with a tensile strength of 55,000 psi. TUBE ID WALL THICKNESS (in) WALL THICKNESS (in) (in) 0.055 TUBE TUBE ID (in) 0.430 0.402 0.370 OD (in) 7/8 0.310 TUBE WALL OD THICKNESS (in) (in) 1/8 0.035 3/16 1/4 5/16 3/8 0.035 0.035 0.049 0.065 0.035 0.049 0.065 0.035 0.049 0.065 0.118 0.180 0.152 0.120 0.243 0.215 0.183 0.305 0.277 0.245 TUBE OD (in) 1/2 5/8 3/4 0.035 0.049 0.065 0.095 0.035 0.049 0.065 0.095 0.049 0.065 0.109 0.555 0.527 0.495 0.435 1 1-1/4 0.652 0.620 0.532 1-1/2 0.049 0.065 0.109 0.049 0.065 0.120 0.065 0.095 0.120 0.065 0.095 TUBE ID (in) 0.777 0.745 0.657 0.902 0.870 0.760 1.120 1.060 1.010 1.370 1.310
6. A pump is located 4.5 m to one side of, and 3.5 m above a reservoir. The pump is designed for a flow rate of 6 L s'. For satisfactory operation, the static pressure at the pump inlet must not be lower than -6 m of the water gage. Determine the smallest standard commercial steel pipe that will give the required performance. pump 4.5 m. 1.8 19=d 3.5 m 7. water 90° elbow
1. in a section of horizontal piper with a diameter of 3cm the pressure is 5.21 kpa and water is flowing with a speed of 1.50m/s. the pipe narrows to 2.50cm. what is the pressure in the narrower region if water behaves like an ideal fluid of sensity 1000kg/m3 2. tensile stress a. the ratio of elasic modules to strain b. the applied force per crosssectional area c. the ratio of change in length to the orig length d. the strain per unit legth e. the same as force
A compressor piston has a stroke of 380 mm and the clearance volume of 7% of thestroke volume. At the beginning of compression stroke the pressure of air is 0.99 barWhen the piston has travelled 260 m from the begining of the compression stroke thedelivery valves open and delivers air at 4 bar. Find the value of "n", iif the compressionfollows the law PVn = CA. 1.37B. 1.39C. 1.28D. 126
Problem 3: A turbulent flow in a pipe has a Reynolds number of 200,000. The pipe diameter is 125 mm, andthe surface has the roughness of coarse concrete (use value in table on Moody diagram above for roughnessheight). Find the following:a. The Relative Pipe Roughness (?⁄?): ___________________________________b. Friction factor read from Moody Diagram: ______________________________c. Friction factor calculated with an appropriate formula: ____________________