//Ethane (CnH2n+2 ) is burned with atmospheric air. The analysis of the products on a dry basis is as follows: CO₂=9.7% 0₂=1.7% CO = 2.9% N₂=-85.7% Calculate the air-fuel ratio and the percent theoretical air and determine the combustion equation.

//Ethane (CnH2n+2 ) is burned with atmospheric air. The analysis of the products on a dry basis is as follows: CO₂=9.7% 0₂=1.7% CO = 2.9% N₂=-85.7% Calculate the air-fuel ratio and the percent theoretical air and determine the combustion equation.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter32: Oil Heat

Section: Chapter Questions

Problem 12RQ: When incomplete combustion occurs, what additional by-products of combustion are created?

See similar textbooks

Related questions

Q: Find the angle theta. a = 5. b = 3₁

A: Co-ordinate of the point A ~ (5 , 0 , 0) C~ (0 , 1 , 3) B ~ (0 , -1 , 2) Unit vector in the…

Q: Draw the control volume of a compressor and apply the first law of thermodynamics to it. With…

A: For solution refer below images.

Q: Draw the pictorial isometric view using the two given orthographic projections

A: Refer the below image for the required isometric view for the given orthographic views.

Q: A reheat steam cycle has 13500 kPa throttle pressure at the turbine inlet and 2800 kPa reheat…

Q: A manometer of the shape shown in the figure has limb A filled with water and the limb B with oil…

Q: A flashed steam geothermal power plant is located where underground hot water is available as a…

A: Given data steam enters turbine at saturated condition of 500 kPa steam expands to 15 kPa. hot water…

Q: Determine the state of stress at point A on the cross section of the pipe assembly at section a-a.…

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

Q: Construct the top view of this ortographic figure.

A: According to the details provided in the question, we need to DRAW TOP VIEW

Q: Q3:- A liquid whose coefficient of viscosity is µ flows below the critical velocity for laminar flow…

A: The loss of pressure in a length of 120 m is 11520 N/m2.

Q: Water with a specific heat of 1 BTU/lbm°F is pumped using a 1-hp jet pump from a well that is 20 ft…

A: Given Data The specific heat of water is:C=1 BTU/lbm°F The heat lost is:Q=400 BTU/min The mass flow…

Q: CA 20 water is pumped from a large tanke to a second tand 2 through a pipe system, as shown in the…

Q: Which equation is true? (if point 1 is datum line.) 2m 1.5 m Control volume boundary 1-2 200 mm…

Q: In the figure, the resultant of all forces in y-direction equal to ---

Q: The number 8 is pointed to the 8 oil sump. O oil pump. O air inlet manifold. O water jackets. O 1G

A: The number 8 is pointed to cylinder head cover.

Q: 6. Masses A (2.00 kg) and B (3.00 kg) are connected to each other with string over two pulleys as…

Q: The two rotor blades of 770-mm radius rotate about the shaft at O mounted in the sliding block. The…

Q: A refrigeration using R-410a has a capacity of 320kW of refrigeration. The evaporating temperature…

Q: No. 3. Beam AC carries a concentrated load P at its midspan point B. Determine the depth of the beam…

Q: 9:54 ص DIZVA 46 * In the shown picture, engaging the gears A and C together gives the gear shift…

A: Concept: In given gear box, 1.By engaging gears A and C, the input and output shaft are on same…

Q: flywheel rotated about its center), The tangential acceleration at of point A is calculated to be…

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

Q: According to the figure (flywheel rotated about its center), the normal acceleration an of point A…

Q: Determine the terminal velocity vf of the projectile. Evaluate for o=1.22 m/s², n = 0.27 m ¹, and…

Q: The speed of a car increases uniformly with time from 36 km/h at A to 110 km/h at B during 15…

Q: Sulfuric acid with a specific gravity of 1.98 and viscosity of 26.7 cP is flowing in a 35 mm…

Q: A work group of 5 workers in a certain month produced 500 units of output working 8 hr/day for 22…

A: Given Dataunit=500day=22 day 8hrs/day worker =10unit=7200day=22 day8hr/day

Q: Q1: For the problem in Figure (1), determine maximum allowable load P such that maximum flexural…

Q: Part 7) Looking towards summer, pretend for a moment that you won a scooter. Ya are so excited to…

Q: s) The aluminum machine part is subjected to a moment of M = 75 kN. Determine the maximum tensile…

Q: Q2: Water flow in a pipe as shown in the figure if the velocity of the fluid at section A is 1.8 m/s…

Q: How many cylinders in the engine .uses this crankshaft 間

A: From the figure we can see that there are 4 crank connection is given on shaft. Somoy will…

Q: Q4: Choose the correct answer 1. pressure (P) calculate by (a) [p-pg A), (b) [p-pQh), (c) [p-pg hl…

Q: 2. Calculate the density and specific weight of nitrogen at an absolute pressure of 1 MPa and a…

A: GIVEN DATA- PRESSURE P=1MPa T=40'C = 40+273 =313K R=297 J/KgK WE HAVE TO FIND DENSITY AND SPECIFIC…

Q: If the steam undergoes a process under Pv^1.296 = C, and the work steady flow is found to be 342.47…

Q: Why do viscoelastic solids have a viscous modulus greater than the elastic modulus?

A: The only distinction between elastic and viscoelastic materials is that viscoelastic materials…

Q: Determine the manometer reading as shown in the figure, when the velocity of fluid flowing through a…

Q: A-Liquid bismuth flows at a rate of 4.5 kg/s through a 5.0-cm-diameter stainless-steel tube. The…

Q: The velocity of a fluid flowing in a pipe is to be measured by two different Pitot-type mercury…

A: we have to evaluate which pitot tube will be more accurate

Q: The slider of mass 1 kg attached to a spring of stiffness 400 N/m and unstretched length of 0.5 m is…

A: From A to B At position A vA=0xA=0.5 m At position B vB=?xB=0.707 m-0.5 mxB=0.207 m The given…

Q: 1. 3. 2 6 .7 b

A: GIVEN DATA- A PISTON NOMECLATURE IS GIVEN WE HAVE TO FIND NAME OF POINT 2

Q: Match the following to its correct definition a. boiler b. condenser c. reheater d. open feedwater…

A: Boiler: It is where bled steam and/or water at different temperatures mix. It is where water is…

Q: Home Work: A cantilever shaft (d-20mm) is subjected to tensile load of (P-8 kN) and bending force of…

A: Find , Principal stresses, Maximum shear stress.

Q: 11) The car travels along the circular path such that its speed is increased by a (0.5e) m/s², where…

A: Find , V at 18m. a at 18m.

Q: 4. In what standard plates can we index the following. Solve using sil label each values. a. gear of…

A: we have to determine the plate size for manufacturing the given items by simple indexing

Q: A refrigeration using R-410a has a capacity of 320kW of refrigeration. The evaporating temperature…

A: Refrigerant=R410aRefrigeration capacity, Q˙e=320 kWEvaporating temperature, Te=-10oCCondensing…

Q: 7 Heat is transferred from a tank of water in a refrigerator at(OC) degrees to a tank of boiling…

Q: 5. A 3-in solid aluminum shaft is subjected to two torques as shown. Use G = 4 x 106 psi. Compute…

Q: 6. Compute for the necessary stroke per minute on 8 inches copper if it has 100 fpm as its cutting…

Q: Two reservoirs are connected by 198ft of 2-in diameter tubing. What is the flow rate when the…

A: The calculated flow rate in ft3/s.

Question

//Ethane (CnH2n+2 ) is burned with atmospheric air. The analysis of the
products on a dry basis is as follows:
CO₂=9.7%
0₂=1.7 %
CO = 2.9%
N₂=-85.7%
Calculate the air-fuel ratio and the percent theoretical air and determine the
combustion equation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

C4Hs is burned in an engine with a fuel-rich air-fuel ratio. Dry analysis of the exhaust gives the following volume percents: CO2 = 14.95%, C4H8 0.75%, CO = 0%, H2 = 0%, O2 = 0%, with the rest being N2. Higher heating value of this fuel is QHHV = 46.9 MJ/kg. Write the balanced chemical equation for one mole of this fuel at these conditions. Calculate; a) Air-fuel ratio. b) Equivalence ratio. c) Lower heating value of fuel. [MJ/kg] d) Energy released when one kg of this fuel is burned in the engine with a combustion efficiency of 98%. [MJ]
A hydrocarbon with an unknown composition (CxHy) is burned in dry air. The products are 9.6%CO2, 7.3%O2 and 83.1%N2. Determine the x/y ratio and the percentage theoretical air used.
A sample of coal was found to have the following percentage composition C=75 %, H2 = 5.2 %, O2 = 12.8 %, N2 = 1.2 % and the rest ash. Calculate the amount of air needed for the complete combustion if 1 kg of the coal is burnt with 30 % excess air.
PARTS A & B ( Justify correctly) Gaseous ethane C2H6 is burned at constant pressure P = 1atm. The reagents enter the reaction at 25°C, and the products are at 727°C. Determine the heat released by the system for ethane combustion with PART (a) the theoretical stechiometric amount of oxygen PART (b) the theoretical amount of air (air contains 3.76 kmol of nitrogen per 1 kmol of oxygen). In which case is the heat released by the system larger? Explain .
C,Hs is burned in an engine with a fuel-rich air-fuel ratio. Dry analysis of the exhaust gives the following volume percents: CO, 14.95%, C,H, 0.75%, CO 0%. H = 0%, O, 0%, with the rest being N. Higher heating value of this fuel is Quav 46.9 MJ/kg. Write the balanced chemical equation for one mole of this fuel at these conditions Calculate: (a) Air-fuel ratio. (b) Equivalence ratio. (c) Lower heating value of fuel. [MJ/kg] (d) Energy released when one kg of this fuel is burned in the engine with a combustion efficiency of 98%. [MJ]
Liquid octane is burned completely with 75% excess air. Determine the air-fuel ratio for this combustion process.
Methane is burned completely with 25% excess air. Compute the number of moles of nitrogen in the products of combustion per mole of fuel. Use the editor to format your answer
B// Hexane (C6H14) is burned with atmospheric air. The analysis of the products on a 'dry' basis is as follows: CO₂ = 10.00%, O₂ = 2.37%, CO = 0.53%. (i) Determine the combustion equation; (ii) Calculate the air-fuel ratio; (iii) Percent theoretical air.
Ethane (C2H6) is burned completely with 25% excess air. Show the combustion reaction of fuel and air. Determine the actual air-fuel ratio in kgair/kgfuel.
This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Ethane (C2H6) is burned with 20 percent excess air during a combustion process. Assume complete combustion and a total pressure of 180 kPa. Use data from the tables. CH. Combustion CO, H,0 02, N, chamber Air X kPa 20% excess where X= 180 Determine the air-fuel ratio. (You must provide an answer before moving on to the next part.) The air-fuel ratio is kg air/kg fuel.
Nitromethane Fuel having a chemical formula CH3O2N is burned in an engine at a fuel-air equivalence ratio of 0.84 and a temperature of 920 K. The molar fraction of 02 is: Select one: O a. 0.418 O b.0.089 O c. 0.772 d. 0.022 O e. 0.148
Methanol (CH3OH) is burned with 50% excess air. Write the balanced reaction equations for complete and actual combustion, and then determine (a) the actual air-to-fuel ratio, and (b) the enthalpy of the complete combustion of Methanol at 25°C and 1 atm assuming H₂O in the products is in the liquid form. N₁ hc=Hp-HR=Nphp-ENRIR TABLE 32 Standard enthalpies of formation Species State! 0₁ Gas Gav Ga Gas Gas Gas H₁ C. Co, но 1,0 CO Useful relations: Mair 123 ful C,H, CH,OH CH,OH Liqind Gas Gas Gas Gas Liquid Gas Liquid AF C₂B₁ сн.. At 298.15 K (25 C) and 1 aus Ah,, MJ/kmol 0 0 0 0 -393.52 241.83 285.84 110.54 -74.87 -101.85 -201.17 238.58 208.45 249.35