Question 2 A tubular post of outer diameter d, is guyed by two cables fitted with turnbuckles (see figure). The cables are tightened by rotating the turnbuckles, thus producing tension in the cables and compression in the post. Both cables are tightened to a tensile force of 110 kN. Also, the angle between the cables and the ground is 60°, and the allowable compressive stress in the post is o =35 MPa. If the wall thickness of the post is 15 mm, what is the minimum permissible value of the outer diameter d2? Cable Turnbuckle Post d2 60° 60°

Question 2 A tubular post of outer diameter d, is guyed by two cables fitted with turnbuckles (see figure). The cables are tightened by rotating the turnbuckles, thus producing tension in the cables and compression in the post. Both cables are tightened to a tensile force of 110 kN. Also, the angle between the cables and the ground is 60°, and the allowable compressive stress in the post is o =35 MPa. If the wall thickness of the post is 15 mm, what is the minimum permissible value of the outer diameter d2? Cable Turnbuckle Post d2 60° 60°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum alloy pipe with an outside diameter of 5.7 in. and a wall thickness of 5/16 in. cantilevers upward a distance of L = 12 ft. The pipe is subjected to a wind loading that increases from wA = 7 lb/ft at its base to wB = 11 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?
Two steel [E = 30,300 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.125 in. and a wall thickness of 0.265 in. Pipe (2) has an outside diameter of 3.500 in. and a wall thickness of 0.206 in. Assume L₁ = 13 ft and L₂ = 19 ft. If the normal stress in each steel pipe must be limited to 20 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ (a) Pr max (b) VB= (2) (1) i i C B kips in.
Kindly quick as possible
A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A.
(32 H.W Find longitudinal and hoor tensile stresses in the Wall of vessel Shown in figure, if the internal pressure. is 0.9 MPa and thickness of Wall is 6.4mm ? Ans: 6 = 42.19 MP₂ °H = 62.8 Mra 4 Also find I ?=0.67 Alir G 0.6m fot TE L = 1.8m O 7 0.6m
Can someone please answer this? Thank you, in advance.
3. A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A. 300 kN A V 300 kN
The copper pipe shown in the figure has an outside diameter of 3.000 in. and a wall thickness of 0.383 in. The pipe is subjected to a uniformly distributed torque of t = 87 lb-ft/ft along its entire length. Using a = 2.00 ft, b = 4.50 ft, and c = 7.75 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe. Answers: ccccccccc.com (a) TA= a (b) TB = i b i psi psi
Two steel [E = 30,700 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 6.125 in. and a wall thickness of 0.286 in. Pipe (2) has an outside diameter of 4.000 in. and a wall thickness of 0.209 in. Assume L₁ = 13 ft and L₂= 21 ft. If the normal stress in each steel pipe must be limited to 24 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ Answers: (a) Pmax= (b) VB= (2) (1) tel i tel P C B kips in.
Solve this question as soon as I upvote solution
The copper pipe shown in the figure has an outside diameter of 4.000 in. and a wall thickness of 0.363 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.00 ft, b = 4.00 ft, and c = 7.5 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe. a b Answers: (а) ТА i psi (b) Тв- i psi
An aluminum alloy pipe with an outside diameter of 4.3 in. and a wall thickness of 5/16 in. cantilevers upward a distance of L = 22 ft. The pipe is subjected to a wind loading that increases from wA = 8 lb/ft at its base to wB = 12 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?