Question 1: The frame consists of right-angled triangles each of base 2 m with angles as shown. It is supported vertically at pins F and D and is subjected to the loading shown at pins A, B and C. (a) Determine the support reaction at pins F and D. (b) Use the method of joints to determine the type (tension or compression) and the magnitude of the force in each member of the frame. 40 kN 75 kN B 25 kN 90°/60° 90 60 D AL60°

Question 1: The frame consists of right-angled triangles each of base 2 m with angles as shown. It is supported vertically at pins F and D and is subjected to the loading shown at pins A, B and C. (a) Determine the support reaction at pins F and D. (b) Use the method of joints to determine the type (tension or compression) and the magnitude of the force in each member of the frame. 40 kN 75 kN B 25 kN 90°/60° 90 60 D AL60°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem #3 The truss shown below is supported by a pin at A and a roller at G. Loads are applieu at joints M, L, and I as shown. The support reactions are: Ax = -70 kN, A, 56 kN, and Gy 64 kN (positive axes directions are shown). Determine the forces in members IJ, IE, KD, and AN. 50 kN 50 kN 50 kN M K Notes: 1. Show all work, and put units on your 4 m answers. 2. CLEARLY indicate if the member is in tension or compression – use T' for a member in tension and C' for a member in compression G. В D E F 18 m, 6 @ 3 m
From the truss shown in the figure (a) Calculate the left and right support reactions for the truss. For the left handside reaction, provide the magnitude and direction of the horizontal andvertical components.(b) Using the method of joints or method of sections, calculate the forces in themembers a, b, c, d, e, f, and g. For non-zero forces, state tension orcompression for each member.
3.) Consider the 2D simple-truss shown below where point A is connected via a pin, and point D is connected via a roller. P1= 9.6 kN, P2= 13.0 kN, P3 = 8.5 kN. %3D a) Identify and label all reaction forces (on the diagram) b) Solve for the values of all reaction forces c) Solve the force in each of the members using the method of joints
Situation 4: Given the truss shown, determine the maximum value of the downward force P if the allowable stresses would be 100 MPa in tension and 75 MPa in compression. The area of each truss member is 120 mm². 8 m 9 m B 6 m C P A. Maximum force P (N)
The truss is subjected to the loading shown. It is supported by a pin at A and a roller at L. Determine the force in members FH, HG and GI, and state if the members are in tension or compression. Present a FBD for every analysis performed. 2.4 kips 0.8 kip 1.6 kips B с 1.6 kips 8 ft D E 8 ft F G 8 ft 1.6 kips 8 ft H 1.6 kips 8 ft J K 0.8 kip obdo 8 ft 6 ft L 14.5 ft
Question 1: The frame consists of right-angled triangles each of base 2 m with angles as shown. It is supported vertically at pins F and D and is subjected to the loading shown at pins A, B and C. (a) Determine the support reaction at pins F and D. (b) Use the method of joints to determine the type (tension or compression) and the magnitude of the force in each member of the frame. 40 kN 75 kN 25 kN 60 90°V60° 90 A 60
The bridge is pinned at A and has a roller at G. A downward load of 12.5 lb is applied at point C, and a downward load of 25 lb is applied at E. The support reactions at the pin and roller are shown on the image. Find the stress in members making up the bridge using either the method of joints or method of sections.
Question 1: The truss is subjected to the system of forces as shown in the following figure. The truss Is supported bya pin at A and a pin at E. Determine, using the method of joints, the force in members (BA), (BE), and (DE) of the truss and Indicate if these members are in tension (T) or compression (C). Set P P2 = 4 kN. 30 30° D. 3 m 3 m
4. Use the method of joints to determine the internal forces in each member of the truss. The structure is supported by a roller at A and a pin at D. E 2 m B 400 N 2 m D O 2m
The four-member “A” frame is supported at A and E by smooth collars and at G by a pin. All the other joints are ball-and-sockets. If the pin at G will fail when the resultant force there is 800 N, determine the largest vertical force P that can be supported by the frame. Also, what are the x, y, z force components which member BD exerts on members EDC and ABC? The collars at A and E and the pin at G only exert force components on the frame.
Using the method of joints, determine the force in each member of the truss shown below (solve for FAB, FAD, FBD, FDE, FBE, FBC, and FCE. Using Inverse Method) 2000 lb 1000 lb B -12 ft D -12 ft- E cl 8 ft 12 ft 6 ft 6 ft Hints: 1. The reaction at the roller support at E is 10,000 lbf upwards. 2. The reaction of the support at C is 7,000 lbf downwards.
Determine the force in member AB, FE and CD using method of section. A |– 3 m →✦✦✦▬▬4 m —✦✦✦▬ 3 m →| -4 B C 60 kN E D T 3 m 4 m 3 m