QUESTION 1 rom the figure below, locate the cat id fx and y axes as shown. Y y2 y1 x1 x2 y1 y2 y3 x1 20 16 12 8 5 x2 inch inch inch inch inch ANSWER IN THREE (3) DECIMAL PLACES INCLUDING ZEROS Total Area = in ² y3

Q: The frame shown in Figure is supported by a hinge at E and a roller at D. Compute the horizontal and…

A: Given data,  Load = 24 kN Angle = 45°

Q: Calculate the volume V of the solid generated by revolving the 65-mm right-triangular area about the…

A:

Q: Determine the shear and moment throughout the beam as functions of x. (200+ N)lb -X- 4 ft |A. (100+…

A:

Q: The quarter cylindrical gate AB has a radius of 1.5 m and length 2.4 m perpendicular to the paper.…

A: Hydrostatic force is defined as the resultant force due to the pressure load of a liquid acting on a…

Q: QUESTION 6 For a horizontal curve with the following pargmeters what is the station of the PT? Give…

A: Horizontal Curve: The horizontal curve occurs at the intersection of two highways. The curve which…

Q: An oil of specific gravity 0.8 is flowing a venturi meter having inlet diameter 20 cm and throat…

A: Given- Specific gravity of oil SGoil=0.8, Inlet diameter D1=20 cm=0.20 m, Throat diameter D2=10…

Q: Gasoline has a specific weight of 42.5 lb/ft³, flows in a pipe enlargement from 2.05 in. iameter to…

A: D1=2.05in D2=3.71in To find velocity v1

Q: Determine the magnitudes of the reactions at A and B for the beam loaded as shown. Answers: A = B =…

A:

Q: Gasoline has a specific weight of 42.5 lb/ft³, flows in a pipe enlargement from 2.05 iameter to 3.71…

A: D1=2.07in D2=3.71in To find velocity v1

Q: If a trenching machine with an average digging speed of 3.6 ft/min is used to make a 1500 feet-long…

A: Given: Digging speed= 3.6 ft/min Trench length= 1500 ft Efficiency = 45 min per hour =0.75 To find :…

Q: A quadrilateral ABCD (violet) is subjected to axial and shear forces transforming it into a right…

A: The given figure is shown below:

Q: Determine the location of the shear center O of a thin-walled beam of uniform thickness having the…

A:

Q: The following data were obtained by conducting liquid limit and plastic li tests on a soil collected…

A: To determine: a) Draw the flow curve and determine the liquid limit b) Using the Casagrande…

Q: Determine the reactions at supports. Also, draw the shear and moment diagram. Note: c= 8 d= 1

A: Given Data c = 8 d = 1  Find support reaction and draw shear force and bending moment diagram.…

Q: Q1. Find the horizontal thrust of the water on each foot of width of the sluice gate, given y₁ = 7…

A:

Q: Thanks for the answer!. If the material used was reinforced concrete, Would it have the same type of…

A: This question is related to the Concrete Technology from Civil Engineering. This is combined problem…

Q: What is the equivalent static force (in kips) if pseudo-acceleration is 2.34g and the weight of the…

A: Given: Weight of vibrating structure= 75 Kips  Pseudo acceleration= 2.34g Required: Equivalent…

Q: Determine the density of metallic body which floats at the interface of mercury of sp.gr 13.6 and…

A: Given Data  Specific gravity of mercury = 13.6  Volume of body submerged in mercury= 0.4 V  Volume…

Q: The two bars, pinned together at B, are supported by a frictionless surface at A and a built-in…

A: ∑MB=0RA cos50°×1.2-900×1.2×1.22=0RA=840.09 N

Q: An experimental device imparts a force of magnitude F = 50 lb to the front edge of the rim at A to…

A: Draw the free body diagram as follows:

Q: Dron Acompound steel [G=80 GPa) shaft consists of a solid 110-mm-diameter segment (1) and a solid…

A: Given data,  G = 80 GPa Solid shaft 1 diameter = 110 mm Solid shaft 2 diameter = 56 mm Allowable…

Q: For an aircraft to take off from Sydney. airport, the required length of runway at sea level in…

A:

Q: Air at standard conditions flows over a flat plate. The free stream speed is 3 m/s. What is the…

A: Given : Stream speed = 3 m/s Kinematic viscosity of air = 1.5 X 10-5 m2/s Density = 1.23 kg/m3 To…

Q: Determine the reaction at B for the beam shown below. 100 KN -3 m O a. By=115 kN ↑ O b. By = 120 kN…

A: Given,  UDL = 20 kN Point load = 100 kN Length of beam = 12 m

Q: The lower sand layer in the soil profile shown below is in an artesian condition. Calculate: 2 a)…

A: Given data : It is a multipart problem from Soil Engineering/Mechanics or Geotechnical Engineering.…

Q: A triangle inscribed in a semi-cirice with radius r shown below. Locate the centroid from point O.…

A: To find centroid moment of inertia with respect to x axis

Q: The effective stress at a point located at a depth of 5.5 ft in a saturated soil (γm = 108 lb/ft3,…

A:

Q: Draw the shear and moment diagrams for the beam. 6 kN 12 kN/m -6 m- B- 3 m.

A: Given : This is a problem from structural analysis where we are asked to determine the shear and…

Q: A body of dimensions 1.5 m x 1.0 mx 2 m, weighs 1962 N in water. What is the weight of the body in…

A:

Q: As per IS 800, the efficiency of a riveted joint having the minimum pitch is: 1. 60%

A: Problem from steel structure, Where we are asked to determine the efficiency of a riveted joint…

Q: Elevation (meters) 2. Given the figure below, in which dashed lines indicate equipotential lines and…

A: The given figure is shown below:

Q: Q1/ The average price of gasoline in 2005 was $2.31 per gallon. In 1993, the average price was…

A:

Q: A Determine its smallest thickness b if its width is 56. Assume that it is fixed connected at its…

A: Given : Applied load = 600 lb L = 9.6 ft To Find : The smallest thickness b if its width is 5b.

Q: A wooden cylinder having a specific gravity of 0.6 has a concrete cylinder of the same diameter and…

A:

Q: Q6) Use the Müller-Breslau principle to sketch the influence lines for the vertical reaction at A,…

A:

Q: 3. By using the left side of the figure. determine the force in members FH, FG, and EG by using…

A: A truss is given with roller support at A and hinged support at K Degree of static indeterminacy, Ds…

Q: PROBLEM a.) Find the reaction forces and the force in each of the members of the truss shown by the…

A: Given Data  Find the support reaction and forces in each member using method of joints.

Q: the centroid location formulas on step 2 come

A:

Q: Three identical steel balls, each of mass m=80kg, are placed in the cylindrical ring which rests on…

A:

Q: Q- Using a sleeper density of n+5, find out the number of sleepers required for constructing a broad…

A: Given data: Sleeper density = n+5 Railway track length = 0.64 km

Q: A stone weighs 650 N in air and 275 N in water. Calculate its specific gravity.

A:

Q: Determine the z-coordinate of the centroid of the rectangular solid with the hemispherical hole. The…

A:

Q: For the design of the band brake shown, find the couple M required to turn the pipe in the V-block…

A:

Q: ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LNG…

A: Given, to determine,  the coordinates of the centroid of the plane region shown

Q: Question 6 Calculate the radius of a turn out for a data given below:- G = 1.67 m, D = 13.3 cm & N =…

A: Given- Gauge length G = 1.67 m, D = 13.3 cm & N = 12 Angle of switch Φ = 108’ The radius of a…

Q: 3) Determine deflection at point C and slope at point D using double integration method (El is…

A: Given: EI - constant To find: The deflection at point C. The slope at point D.

Q: arm bone through the elbow joint. Two muscles, the triceps and the biceps, are attached to this…

A:

Q: Following are the measured values of the angle 'A' with their respective weights. ZA = 56°15'00';…

A:

Q: PART 3. Determine the reactions at supports. Also, draw the shear and moment diagram per member.…

A:

Q: The beam shown in the figure has a roller support at A, a fixed support at C and an internal hinge…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.