Question 1 (a) Sketch the I-V curves of an ideal diode and a real germanium diode. Label the sketched diagrams clearly. (b) A circuit is shown in Figure 1. The diodes are silicon type with forward biased voltage of 0.7V. (1) (ii) (iii) (iv) D₁ +10V D₂ ID1 ID2 6ΚΩ B -10V 3ΚΩ A Figure 1 Calculate the diode current for ID1 and /D2. Determine the biasing conditions of diodes D1 and D2. What are the voltages between nodes A and B? Calculate the voltages at nodes A and B.

Question 1 (a) Sketch the I-V curves of an ideal diode and a real germanium diode. Label the sketched diagrams clearly. (b) A circuit is shown in Figure 1. The diodes are silicon type with forward biased voltage of 0.7V. (1) (ii) (iii) (iv) D₁ +10V D₂ ID1 ID2 6ΚΩ B -10V 3ΚΩ A Figure 1 Calculate the diode current for ID1 and /D2. Determine the biasing conditions of diodes D1 and D2. What are the voltages between nodes A and B? Calculate the voltages at nodes A and B.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
What is CEMF?
Draw vx and v0 according to the input voltages in the circuit shown in the figure. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, the threshold voltages of diodes will be VE = 0.7V.
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform
For the given circuit, assume the diode D1 and D2 are the ideal diodes. The average value of the voltage Vab (in volts) across the terminal A and B is
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
1- ) Determine the output voltage and diode currents ipi and iD2 for the circuit shown for the two values of input voltage V₁ = OV and V1 = 4 V. Assume that diodes have 0.7V constant voltage drop. 5 V1 le iD1 D1 # R1 10k V2 + --1₁ 5V ..e D2 Vo 5k V3 HOE R2 SV
Draw output waveform for the following circuit. Suppose input is a pure square wave with a positive half at 10 V and negative half at -10 V for ideal diodes. D1 D2 220 R3 R1 1k R2 1k
For the circuit below, assume the diodes operate with a constant voltage drop of .7V, find Vx, Vy, VD4 and ID2. 15V 15V Allt V1 V2 R1 1k IDC 1mA Vx R2 2k ww D1N4002 Vy D1N4002 7D1 D1N4002 D2 D3 R3 1k D4 D1N4002