Question 01: Colpitts oscillators Consider the MOSFET Colpitts oscilaltor circuit given in the figure below and let L = 10 µH, C1 = 60 pF, C2 = 50 pF, and C3 = 0 pF RFC -o +VDD L Note: RFC is the RF choke inductor and is used only to block the AC signal from reaching the DC supply. 1. Derive the governing equation and determine the frequency of oscillation and the minimum amplification factor needed for sustained oscillations. 2. The capacitor C3 is replaced with a variable capacitor to allow tuning the oscillator. If the capacitance of C3 can vary from 5 to 50 pF and calculate the frequencies of ocillation for the two adjustment extremes and the minimum value of amplification factor needed to ensure oscillation throughout the full tuning range.

Question 01: Colpitts oscillators Consider the MOSFET Colpitts oscilaltor circuit given in the figure below and let L = 10 µH, C1 = 60 pF, C2 = 50 pF, and C3 = 0 pF RFC -o +VDD L Note: RFC is the RF choke inductor and is used only to block the AC signal from reaching the DC supply. 1. Derive the governing equation and determine the frequency of oscillation and the minimum amplification factor needed for sustained oscillations. 2. The capacitor C3 is replaced with a variable capacitor to allow tuning the oscillator. If the capacitance of C3 can vary from 5 to 50 pF and calculate the frequencies of ocillation for the two adjustment extremes and the minimum value of amplification factor needed to ensure oscillation throughout the full tuning range.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. An RC filter stage (R = 33 0, C = 120 HF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage. *****END*****
• Design a classical rectifier to deliver 100W into a resistive load from a 120V, 60HZ mains. ac Quantify the effect for different values of filter capacitance on: >average output voltage >output voltage ripple >Input current shape, harmonic content and THD
You are tasked to look for a converter circuit design that has the specifications tabulated in Table I. The aim is to produce an output voltage of 20 V which can be used to drive a load of 120 W. The converter must operate in CCM. Table I: Design Specifications Design Parameters Input voltage Switching frequency Output current ripple Output voltage ripple Values 35 V 60 kHz 5 % 1% a) Sketch the final converter and label all parameter values b) Sketch the final operating waveforms and label all parameter values c) Determine Ve.min and Vemax- Check if the output voltage ripple matches with the design requirement.
-4) Design a circait containing a comparater with a hy steresis loop a. Draw the circuit with all values of the components required for the dksign. b. What is the name of the circuit in (a). c. Sketch the output waveform when the input is a 15-V peak sine wave. d. Adjust the value of RI in the circuit such that the hysteresis width will be 10.
uo A:EV * ll. pluli ► b89f3244-f736-4021-901... PI EXPlain The effect of increasing The filter Capacitance on The outfut Voltage in The haif - wave rectifier and filber Circuit ? CS Scanned with CamScanner
Problem #6: An abrupt p-n junction varactor is used to tune an oscillator shown in Figure 3. At zero bias voltage, the varactor has a junction capacitance of 4pF, Vbi 1.3V for GaAs. The active device has CD = 2pF and RD = 10W. The load bias has L₁ = 15nH and R₁ = 10W. What are the oscillation frequencies at (a) -20V (b) -10V and (c) OV? = L₁ R₁ C₁ (V) -RD FIGURE-3 www CD
A 555 timer configured to run as an astable mode oscillator is shown in Figure 1. If the output is needed to have 30% duty cycle, i) Determine the required value of Rị if R2 = 7kN. ii) Determine the frequency of the output. iii) Draw the charging and discharging phase of capacitor Cext and its relation with the output waveform. ASsume Vcc = 12 V. +Vcc (4) |(8) R1 RESET Vcc (7) DISCH 555 D1 R2 (6) THRESH (3) OUT (2) TRIG (5) CONT GND :Cext 0.01 µF (1) 0.01µF Figure 1
INCLUDE ALL THE DECIMALS.
refer image
Vcc=15V Q1: BC237 Rc 3.6kQ or BC238 B=200 VBE(on)=0.7V R1 110KQ Rs Cci 1000 4.7µF Cco 4.7µF R2 ·27kΩ RE 1.2kQ RL 12kΩ Vs Rin Rout Figure 1. Common-emitter amplifier. 2)
Please answer this question asap
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.