Ql:: A 11 in diamcter of pipes and 14 in long slides along a large diameter cylinder at a speed of 0.5 ft/s under the application of a force of 25 N in the inverse direction of its motion due to a film of oil between the cylinder and pipe. If the viscosity of oil 5 stokes and s.g 0.9, find the thickness of oil and the diameter of cylinder.

Ql:: A 11 in diamcter of pipes and 14 in long slides along a large diameter cylinder at a speed of 0.5 ft/s under the application of a force of 25 N in the inverse direction of its motion due to a film of oil between the cylinder and pipe. If the viscosity of oil 5 stokes and s.g 0.9, find the thickness of oil and the diameter of cylinder.

Name: Ql:- A 11 in diameter of pipes and 14 in long slides along a large di
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Ql:- A 11 in diameter of pipes and 14 in long slides along a large diametercylinder at a speed of 0.5 ft/s under the application of a force of 25 N in the inversedirection of its motion due to a film of oil between the cylinder and pipe. If thevisco

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In shut off valve experiment, the 3/ 6th of valve position, the discharge is found as of 6 lit/s for the 27mm diameter pipe. Find the velocity and Reynolds number of the flow. Take the viscosity of water as 1.14x10 Ns/m?. (Enter only the value in the box by considering the unit given in bracket. Do not write the unit in the boxes) Velocity of water (unit in mm/s) = Reynold's number
1. Two indefinitely long flat plates separated by 3 inches in distance but with a thickness of 5 inches each carry alcohol (5 m/s, 1 Pa·s, S.G. 0.89 (ref. water at 4 degrees Celsius) to a specific destination. Find out what the Reynolds Number is. 2. Calculate the dynamic and kinematic viscosities of water at 350 degrees Kelvin Note: Use perry's handbook for the value
A2 A Newtonian fluid with viscosity (Mu) flows upward at a steady rate between two parallel plates that make an angle y with the horizontal. The fluid thickness h is much smaller than the width of the channel W. The pressures at each end, P(0) and P(L), are known and the pressure variations in the y-direction are small. Assume that Vy and Vz = 0 and Vx is a function of y alone. Use the shell balance to approach : - the Total flowrate, QV
The volume flow in a water pipe is 9000 m°/h. The pipe length is 80 m, the pipe diameter 1 m. The material data of water are a density of 1000 kg/m? and kinematic viscosity v=10® m7s. A steel pipe with roughness 0.05 mm is used. Determine the pressure drop in the pipe.
1.3 A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, determine the pressure in A. 1.4 The absolute viscosity of a fluid at atmospheric conditions is 8 x 10-3 kgf-s/m2. Find this viscosity in: a) Reyn; b) Poise; c) lbf-s/ft2; d) Pa-s.
just part g
A piston having a diameter of 9in. and a length of 995in. slides downward with a velocity V through a vertical pipe. The downward motion is resisted by an oil film between the piston and the pipe wall. The film thickness is 90000 in., and the cylinder weighs 7836lb. Estimate V if the oil kinematic viscosity is 7800 ft'/s and its density 432 slugs/ft.Assume the velocity distribution in the gap is linear.
The velocity distribution in a 0.02 m diameter horizontal pipe conveying carbon tetrachloride (specific gravity = 1.59, absolute viscosity = 9.6 x 10-6 Pa sec) is given by the parabolic equation: v(r)=0.01(0.12- r?), where v(r) is the velocity in (m/s) at a distance r in (m) from the pipe center. What is discharge? O a. 3.13 x-8 m3/s O b. None of the mentioned O c. 1.047 x 108 m3/sec O d. 4.97 x 109 m3/sec
5.4 A liquid, density 801 kg/m³ and viscosity 1.49 cp, is flowing in a horizontal pipe at a velocity of 4.5 m/s. If the diameter of a steel pipe is 2½ in, and its length is 65 m (a) Calculate the friction losses (b) Calculate the friction losses if the pipe is considered as a smooth pipe. Determine the percentage decrease in friction losses.
6. A hydraulic lift (see below) of the type commonly used for greasing automobiles consists of a 280.00 mm diameter ram which slides in a 280.18 mm-diameter cylinder, the annular space being filled with oil film of thickness t = 0.09 mm, having a viscosity 0.3612 kg/(m s). If the rate of travel of the ram is v= 0.22 m/s, find the frictional resistance when 2 m of the ram is engaged in the cylinder. Take the weight of ram as 500 N. Ram Oil film -Fixed cylinder
Need help wuth this engineering problem.
A plate 0.05mm distance from a fixed plate moves at 1.25 m/s and required a force per unit area of 3 Pa to maintain this speed by using an oil of specific gravity 0.65. Find the dynamic viscosity in centipoise and kinematic viscosity in stokes of the fluid between the plates. Calculate the specific weight in kN/m³, density, and the specific gravity of a liquid having a volume of 662900 cm and weight of 55 kN