i need the answer quickly hardness testQ_1)Relationship between hardness and yieldstressQ_2)The difference between the Burnell,Vickers, and Rockwell methodsQ_3)Which of the measurements doyou prefer, which method?Q_4)Find methods other than these three formeasuring hardness

Answered: Q_1)Relationship between hardness and…

Engineering

Mechanical Engineering

Q_1)Relationship between hardness and yield stress

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A) An engineer works for a company that has many gray cast iron rods of different diameters and would like to design an equivalent rod that could handle a force of P= 10.0 kipkip without fracturing. What is the minimum diameter that this new rod must have to support P? B)A tensile test is being conducted on a steel-rod specimen with a gauge length of L0 = 4.0 in and an initial diameter of d0 = 0.75 in. If the final length of the rod at fracture is Lf= 5.53 in , find the percent elongation of the rod at fracture.
مختبر Q1/a_ Assume a Brinell test uses a 10 mm steel ball and 3000 kg Joad. If the value of Brinell hardness number is 302. A) What is the diameter of the spherical impression on steel test piece? B) What are the sources of errors encountered in hardness test?
a) Compression tests are generally performed on brittle materials-why?b) How a cast iron specimen fails under compression load?c) Define secant modulus?
Question 8. The following figure represents three hardness-testing techniques of materials. Describe their specifications, how there are conducted and their potential applications? 8 - Shape of Indentation Test Indenter Side View Top View Load Brinell 10-mm sphere P of steel or tungsten carbide Vickers Diamond 136° microhardness ругamid Rockwell and 60 kg) 100 kg } Rockwell 150 kg) Diamond 120° superficial cone: s - in.- diameter Rockwell 15 kg 30 kg } Superficial Rockwell 45 kg) steel spheres
The following data are obtained from the Charpy impact test of a copper specimen. a) Length of the square cross-section specimen = 70 mm b) Each side (top & bottom) of the cross-section = 9.64 mm c) V – Notch thickness at middle of the specimen length = 1.06 mm d) Impact Strength = 279 kJ/m? Determine the Cross-sectional area at the top surface, Cross-sectional area at notch & Impact energy of the copper specimen.
hings The following results were obtained during a tensile test to destruction on a mild steel test piece of diameter 15.96mm and 80mm gauge length Extension for a load of 40KN = 0.08mm Maximum load applied during test = 93kN Diameter at fracture = 12.85mm %3D Final length between gauge points 106mm From these results, determine: i) The modulus of elasticity for mild steel ii) The tensile strength iii) Percentage of elongation iv) Percentage of reduction in area
The following data are obtained from the Charpy impact test of a copper specimen. a) Length of the square cross-section specimen = 70 mm b) Each side (top & bottom) of the cross-section = 9.64 mm c) V - Notch thickness at middle of the specimen length = 1.06 mm d) Impact Strength = 279 kJ/m? Determine the Cross-sectional area at the top surface, Cross-sectional area at notch & Impact energy of the copper specimen. Solution: 1. Cross sectional area at the top surface 92.9296mm^2 2. Cross-sectional area at notch 82.7112mm^2 3. Impact Energy 23.0764248J
a What is the difference between vicker hardness test and brinell hardness test based on load ,indenter , accuracy ? b . what is the meaning of toughness in material science ? c . the toughness of material is affected by what ? d . what is the difference between tensile test and impact test?
Hot working is a good way to shape brittle material 1) True 2) False
Question One a) In a tensile test, material mechanical properties are determined by relating deformations to the applied forces. i. Sketch a typical specimen used in such tests and on it indicate two important dimensions i Sketch the difference you would cxpect in tensile and compressive deformations Sketch a stress-strain curve/graph you would expect from such a test and on it indicate how you would obtain (1) Young's modulus, E(2) clastic limit,oei(3) yield strength ay and (4) ultimate tensile strength duTS ii. b) In such a test, as the one in (a) above, a specimen manufactured from steel, and had an original diameter of 12.8 mm and gauge length of 50.8 mm. The resulting data, stress and strain, is listed in the table below. Strain 0.007 0018 0.032 005 0 052 0.056 0.06 0.005 0072 0.076 011 0.15 017 022 024 (m/ m) Stress 80.8 218 390 540 600 630. 650 640 634 643 745 851 885 815 770 (MPa) By plotting stresses on the vertical axis and strains on the horizontal axis, plot a stress-strain…
Discussion / 1-What is hardness and what is the benefit of calculating it? 2- Classify the materials that have the highest hardness? 3-What does the change of metal type of Brinell ball depend on? 4-What are the means of developing a Brinell test device from your point of view? 5-How does the accuracy of the results in the experiment depend ? V jjo V
The following engineering tensile properties are given for the 1080 steel:-Yield strength (MPa): 585-Tensile strength (MPa): 965-Elongation to fracture for specimen of 5cm gage length (%): 12A 5cm long circular rod of 1080 steel specimen with a diameter of 1.28cm isloaded to failure in tension. a) What was the maximum load needed to break the specimen?(20 points)b) If necking initiated at 80% of the total elongation, prior to this point thespecimen deformation is uniform, compute the true stress at the point ofnecking initiation.