Q6. The flyback converter given in figure has the followingparameters:Va-24 VR=50NN2C = 200 µFSwitching freq. f= 20 kHzNI/N2 2Determine the following:Figure 10-6(b) on page 308from Mohan's Booka. The required duty ratio D to obtain output voltage of V.-5b. The output voltage ripple (in percentage)

Q6) A Fly back converter has, Supply dc voltage (Vd)= 24 V Resistance (R)= 5 ohm Capacitance (C)=…

Q6. The flyback converter given in figure has the following parameters: 字 Va 24 V R=50 C=200 µF Switching freq. f, = 20 kHz N/N2 2 Va %3D Determine the following: Figure 10-6(b) on page 308 from Mohan's Book a. The required duty ratio D to obtain output voltage of V.-5 b. The output voltage ripple (in percentage)

Q6. The flyback converter given in figure has the following parameters: 字 Va 24 V R=50 C=200 µF Switching freq. f, = 20 kHz N/N2 2 Va %3D Determine the following: Figure 10-6(b) on page 308 from Mohan's Book a. The required duty ratio D to obtain output voltage of V.-5 b. The output voltage ripple (in percentage)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1) AC power in a load can be controlled by using a. Two SCR's in parallel opposition b. Two SCR's in series c. Three SCR's in series d. Four SCR's in series 2) The advantage of using free - wheeling diode in half controlled bridge converter is that a. There is always a path for the ac current independent of the ac line b. There is always a path for the dc current independent of the ac line c. There is always a path for the dc current dependent of the ac line d. There is always a path for the ac current dependent of the ac line 3) Silicon controlled rectifier can be turned on a. By applying a gate pulse and turned off only when current becomes zero b. And turned off by applying gate pulse c. By applying a gate pulse and turned off by removing the gate pulse d. By making current non zero and turned off by making current zero
The DC value of a full-wave rectified voltage with a peak value of 55 V is a.) in bridge-type b.) in center-tapped
Draw the waveform of the given clipper circuit and determine the following: a.) At 0V, what is the output voltage?b.) At +20V, what is the output voltage?c.) At -5V, what is the output voltage?
The positive peak value of output waveform for the given circuit diagram is. Bias voltage is 2 V, Diode is germanium) (VPP of input is 18 V, V VouT
Determine the peak value of the output voltage for the figure shown if the turns ratio is 0.5?
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.
Compare both the amplitude and waveform outputs of a parallel and series-positive limiter.
what is the difference of MOSFET and Diode in Boost Converter. Can you also sight an example?
Draw the circuit diagram of DC to DC converter using switched capacitor.
In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230v (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di v: = VmSin ot Vs V. + Vy = VSin ot D2 Full-wave rectifier. Circuit operation during positive half cycle ell + ミ」
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.