A single phase full converter is connected to a 120 V, 60 Hz supply. It has a RL load having L=6.5 mH, R=0.50 and E = 10 V. The average output voltage VpC = 54 V. The output average current is assumed constant equal to Ia. If the average thyristors current ITh a is equal to 44.04A, then the average output current I, would be equal to. !!

A single phase full converter is connected to a 120 V, 60 Hz supply. It has a RL load having L=6.5 mH, R=0.50 and E = 10 V. The average output voltage VpC = 54 V. The output average current is assumed constant equal to Ia. If the average thyristors current ITh a is equal to 44.04A, then the average output current I, would be equal to. !!

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Similar questions

The three phase converter with an ac side inductance L2 25 uh and VLL equal to
2.A Boost converter has an input voltage of 5V and required output voltage is 15V at 25KHzwhen L=150µH and C=220µf and average load current of 0.5A.Determine i) Duty cycle ratio ii)peak to peak ripple current through inductor iii) peak to peak ripple voltage iv) critical values of L & C
the way of work buck dc-to-dc converter
Single phase full wave controlled converter circuit is powered by a single phase source. When the trigger angle is 0 °, the DC output voltage taken from the output of the converter circuit is 300V. If the trigger angle is 60 °, what is the value of the DC output voltage to be obtained at the output? i have 1 houre
A step down converter is operated with a duty cycle of k 0.75. The input voltage is V, 20V. and the load is L=5mH, R=152 The minimum inductor current is I 0.1A. The maximum inductor current is %3D %3D Select one: O a. 0.9 A O b. 1.9 A O C. None of these O d. 1.1 A O e.2A
A single phase semi converter, connected to 230 V, 50 Hz source is feeding a load R = 402 in series with large inductor that makes the load current ripple free. If the value of firing angle is 45°, then the current distortion factor is
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
Q/ Why is high frequency (Fsw ) used in Buck Converter circuits
The inversion mode is possible in single phase half controlled converter with RL load. Select one: O True O False
A step down converter is feeding an inductive load with R-10 Ohms, L15 mH and E-1sV. The supply is Vs-200v, the switching frequency is 10 kHz and the duty cycle is k-0.5. The maximum peak to peak ripple current in the load is equal to 0.34A. The erage load current la would be equal to: Select one: a. 8.5A O b. 18A Oc 11A O d. None of these
The DC-DC converter below is fed from a 96 V DC source and it is desired to obtain 24 V output voltage on 15 2 load resistors. The switching frequency of the converter is 50 kHz. It is desired that the fluctuation rate in the output voltage should not exceed 1%. VI VL mo ic İR a) What is the minimum required coil inductance? b) What is the minimum required capacitor value?
Name thr converter