Q5) write true or false in the following sentences:1. Load torques which always oppose the motion and change their sign on the reversal of motion arecalled passive load tonques.2. The control rectifier drive has low amature current ripple compare to de to de chopper drives.3. The main difference between dynamic breaking and regenerative braking of de motor is thedisconnection the source from de motor in dynamic braking.4. Two quadrant operation of de motor can be obtained from thee phase semiconverter.5. de-de four-quadrant drives can be supply high power than ac-de four-quadrant drives6. Principle of regenerative brake control of de motor applied by using :step down choppers.7. The main disadvantage of stator voltage control of induction motor is low speed rang.8. For speed higher than rated speed of DC motor its required to apply armature control9. A stepper mntor is brushless de motor whose otor mtates in continuous angular displacements.10. In permanent magnet synchruneIs machines, the reluctance of direct axis is always greuter than thequadrature axis reluctance.

We are authorized to answer only 3 question at a time since you have not mentioned which question…

Q5) write true or false in the following sentences: 1. Load torques which always oppose the motion and change their sign on the reversal of motion are called passive load torques. 2. The control rectifier drive has low anmature current ripple compare to de to de chopper drives. 3. The main difference between dynamic breaking and regenerative braking of de motor is the disconnection the source from de motor in dyTiamic braking.

Q5) write true or false in the following sentences: 1. Load torques which always oppose the motion and change their sign on the reversal of motion are called passive load torques. 2. The control rectifier drive has low anmature current ripple compare to de to de chopper drives. 3. The main difference between dynamic breaking and regenerative braking of de motor is the disconnection the source from de motor in dyTiamic braking.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

380 V, 50 Hz, 2p = 6, star connected induction motor impedance in ohms per phase values:R1 = 0.3, X1 = j0.45, R2 = 0.15, X2 = j0.45, Xm = j15Its total mechanical losses are 500W. Core losses are negligible. For a rotor slip of 0.01 at rated voltage, calculate the following:1-rotor speed2-Input active power3-Stator copper losses4-air gap power5-Transferred power and Output power6-shaft moment7-efficiency
What is the use of commutating poles in a DC machine?
The 1 phase equivalent parameters of a three phase 60 Hz, 6 pole 220, star connected, 7.5 KW asynchronous motor are as follows:a) In the case where slip is 0.03, the stator transferred rotor current, the torque and power induced in the motor.b) Maximum torque and angular velocity at this moment and speed value in rev / min.c) Developing torque and developing load currentd) Draw 1 phase equivalent circuit?
I need the answer as soon as possible
w5
a 220v dc shunt motor takes 5a and 40a at no load and full load respectively it has an armature resistance of 0.2 ohm and field resistance of 110 ohm respectively. iron,friction and windages losses are negligible.then using among parameters find following. calculate emf at full load of dc motor
Q3 A - Why the de shunt motor running at the infinity speed? B – Discuss the difference between D.C shunt motor and D.C series motor at load.
Three phase induction motor has rating of 50 kW, 960 rpm, 400 V. 50 Hz, 6-pole. The motor parameters are R = 0.08 N, R' = 0.1 N, X = X = 0.3 N and the moment of inertia 10 kg m². It is required to stop the motor from its no load speed under reverse breaking operation. Find the required value of external resistance that need to put in rotor circuit such way that breaking will be achieved with minimum time. What is breaking time.
For a load such as PWM adjustable speed drives, the true power factor is equal to the displacement power factor. " True False
٣
1. What is the formula for torque production in a single-phase induction motor? Draw a vector diagram for capacitor start single-phase induction motor.2. Which type of starter is popular for using in induction motor and why?
in a DC motor why and how the gain K is affected by the amaurtue resistant and induance ? whats the actual units for K. For tau is affect just by taking induance over resistant? thanks