Q4. ANALYZE THE GIVEN STRUCTURE USING THE MOMENT DISTRIBUTION METHOD NOTE: STOP AT THE 5TH ITERATION (BAL5) 80 KN 8.0m A (B) 6.0m 4.0m A. THE MAGNITUDE OF THE INTERNAL MOMENT AT SUPPORT A IN KN.m? B. THE MAGNITUDE OF THE HORIZONTAL REACTION AT SUPPORT D IN KN? C. THE MAGNITUDE OF THE INTERNAL MOMENT AT JUNCTION C IN KN.m?

Q4. ANALYZE THE GIVEN STRUCTURE USING THE MOMENT DISTRIBUTION METHOD NOTE: STOP AT THE 5TH ITERATION (BAL5) 80 KN 8.0m A (B) 6.0m 4.0m A. THE MAGNITUDE OF THE INTERNAL MOMENT AT SUPPORT A IN KN.m? B. THE MAGNITUDE OF THE HORIZONTAL REACTION AT SUPPORT D IN KN? C. THE MAGNITUDE OF THE INTERNAL MOMENT AT JUNCTION C IN KN.m?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 2: The frame shown below has a fixed support at A and a pin support at C. El is constant. Use the SLOPE-DEFLECTION METHOD to: 8 m a. Find the internal moments (MAB, MBA and MBC) using the Slope-Deflection method and find all reactions b. Draw the Shear (V) and Moment (M) diagrams (clearly show peak values, signs, and location) 3 kN/m B A * 12 m C
PART II. (BEAMS AND FRAMES : SHEAR AND BENDING MOMENT) DIRECTION : Answer the following questions. Provide complete and clear solution with illustration. PROBLEM N0. 1 Determine the reaction at supports B and D. Determine the maximum positive shear and maximum positive moment of the beam below using graphical method (Shear and Moment Diagram) 5 ΚN/M 4 KΝ/M 6 KN/M A B E .0 m- -4.0 m 4.0 m· -2.0 m D
Q.2) (a) Find the support reactions of the beam shown below. (b) Write shear-force and bending moment equations of the beam as a function of distant 'x' from the left-end A of the beam. 11 kips/ft 9 kips/ft 5 kips/ft A В C |D E 6 ft 6 ft 6 ft 6 ft
! Construct the shear-force and bending moment ; For the frame shown below, determine the diagrams and sketch the elastic curve for the beam loaded as shown below. Also determine the shear force and bending moment at point X, 4 m from A. degree of indeterminacy and compute the reactions at D. El=constant. 33 KN/m 36 KN/m 24 KN/m | 20 KN B 5 m 6 m 2 m 40 KN D IA 6 m 4 m 2 m 2 m ) Assuming that beams are framed into girders in simple supports as well as the girders are framed into columns with pin connections, determine the maximum moment and the maximum deflection in an interior girder. Consider load pattern. F.. 5) For the truss shown below, determine the bar force of AB and AD. Also indicate if these forces are tension or compression. The live load is 2.40 KPa 30 KN В 3 m C 3 m 6 m 6 m and the dead load consists D 3 m only of the weight of beams and girders that 3 m No joint 3m are 1 KN/m and 1.4 KN/m, 3 m respectively. The girders I3 m are made of wide flanges with depth 400 mm and 2…
10 ft 10 ft Problem # 1 B 8k ft 10 ft Use the Virtual Work as the displacement method. Determine the reactions at Deflection Curves of Actual, Primary and Structure with Redundant Cy. the supports if the support at C is forced upwards 0.15in. Take E = 29000ksi Bkjt %3D and = 600 in^4. Note: Use Cy as the redundant reaction. Use Compatibility Equation: (+1) 0.15 = -Ac + GScc
1. Calculate the reactions at the support using area - moment method, the slope at the simple support/s,. Use E = 200 GPa and I = 150 x 10 mm4. Draw the shear and moment diagrams. 40 KN 35 kN/m A B 30 kN/m 3m 2m 3m
Determine the moment of the vertical reaction at point A (A,) rotating about the location (XR) of the equivalent resultant force of the forces acting on the beam shown in Figure 3.1f, i.e. A, X XR. Given /= 1.8, P1 = 30, P2 = 20 and w = 10. (Note: Negative "." for clockwise moment.) [Hint: Find the equivalent resultant force and its location (xR) with respect to point A. Apply correct equation of equilibrium to solve Ay. ] P, kN W kN/m P, kN 21 m 21 m Figure 3.1f
2. Determine the reaction at each support and draw the shear and bending moment diagram of the beam shown. Use moment distribution method. 226kN 63.5kN 226kN E ↓ cftt A B D m m 2m m 4 m 4m 21 E = constant G
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam. %3D A -L/2- Part 1 Cut a cross-section through the beam between points A and B, and draw a free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x-3,5 m. M(x) A Answer: M(x) - kN-m + mA, eTextbook and Media
Q3. The 500 N force acting on the frame is to be resolved into two components acting along the axis of the AB and AC. If the component of force along AC is required to be 300 N, directed from A to C. determine the magnitude of force acting along AB and the angle 0 of the 500 N force. . 100N
If the force of the smooth roller at B on the bar bender is required to be 1.5 kip, determine the horizontal and vertical components of reaction at pin A and the required magnitude of force F applied to the handle. 5. 40 in. 60 5 in
a. Calculate reactive forces. b. Plot Shear & Moment Diagrams labeled with pertinent values. c. Calculate centroid of cross-section. 1 in.. d. Calculate Moment of Inertia of cross-section e. Calculate the maximum positive bending stress. f. Calculate the maximum negative bending stress. g. Calculate the maximum shear stress. 25 kips 25 kips 25 kips с D A It 1 ft 2 ft 6 ft E 2 ft B 4 in. 2 in. + a b 1 in.. 1 in. |←4 in.→|